Allied-telesis AT-x230-18GP Manual do Utilizador

C613-04068-00 REV AAT-x230-10GPAT-x230-18GPGigabit Ethernet SwitchesInstallation Guide x230-10GPCONSOLERS-232SDFAULTPOWERSD1000 LINK ACT 10/100 LINK

List of Tablesviii

AT-x230-10GP and AT-x230-18GP Switches Installation Guide1PrefaceThis guide contains the installation instructions for the AT-x230-10GP and AT-x230-18

2Symbol conventionsThis document uses the following conventions:NoteNotes provide additional information.CautionCautions inform you that performing or

AT-x230-10GP and AT-x230-18GP Switches Installation Guide3Contacting Allied TelesisIf you need assistance with this product, you may contact Allied Te

4

AT-x230-10GP and AT-x230-18GP Switches Installation Guide5Chapter 1OverviewThis chapter provides descriptions of the AT-x230-10GP and AT-x230-18GP Gig

Chapter 1: Overview6FeaturesThis section describes the hardware features of the AT-x230-10GP and AT-x230-18GP Gigabit Ethernet Switches.Twisted pair p

AT-x230-10GP and AT-x230-18GP Switches Installation Guide7LEDs Here is a brief description of the port LEDs: POWER and FAULT LEDs; refer to “POWER an

Chapter 1: Overview8Package contents for the AT-x230-10GP SwitchFigure 1 illustrates the package contents for the AT-x230-10GP Gigabit Ethernet Switch

AT-x230-10GP and AT-x230-18GP Switches Installation Guide9Package contents for the AT-x230-18GP SwitchFigure 2 illustrates the package contents for th

Copyright  2014 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 1: Overview10Front and back panels on the AT-x230-10GP SwitchFigure 3 illustrates the front panel of the AT-x230-10GP Gigabit Ethernet Switch.

AT-x230-10GP and AT-x230-18GP Switches Installation Guide11Figure 4 illustrates the back panel of the AT-x230-10GP Gigabit Ethernet Switch.FIGURE 4. A

Chapter 1: Overview12Front and back panels on the AT-x230-18GP SwitchFigure 5 illustrates the front panel of the AT-x230-18GPGigabit Ethernet Switch.F

AT-x230-10GP and AT-x230-18GP Switches Installation Guide13Figure 6 illustrates the back panel of the AT-x230-18GP Gigabit Ethernet Switch.FIGURE 6. A

Chapter 1: Overview14Management softwareThe switches are shipped with the management software pre-installed. The software provides a command line inte

AT-x230-10GP and AT-x230-18GP Switches Installation Guide15Twisted pair portsThe AT-x230-10GP and AT-x230-18GP Gigabit Ethernet Switches feature 8 and

Chapter 1: Overview16Power over Ethernet (PoE)The AT-x230-10GP and AT-x230-18GP switches feature Power over Ethernet (PoE) on the 10/1000BASE-T and 10

AT-x230-10GP and AT-x230-18GP Switches Installation Guide17Cable requirementsThe cable requirements for ports operating at 10 or 100Mbps are given in

Chapter 1: Overview18TABLE 2. TWISTED PAIR CABLE REQUIREMENTS FOR THE 10BASE-T AND 100BASE-TX PORTS AT 10 OR 100MBPSCable type10Mbps 100MbpsNonPoE P

AT-x230-10GP and AT-x230-18GP Switches Installation Guide19Power budget The AT-x230-10GP and AT-x230-18GP switches each have a power budget of 124 an

iElectrical Safety and Emissions StandardsThis product meets the following standards.EMC EN 55022 Class AEN 55024EN 61000-3-2EN 61000-3-3EN 62311FC

Chapter 1: Overview20number of PoE devices so that all of the devices receive power. Otherwise, the switch powers a subset of the devices, based on po

AT-x230-10GP and AT-x230-18GP Switches Installation Guide21Wiring implementationThe IEEE 802.3af standard defines two methods for the delivery of DC p

Chapter 1: Overview22LEDsThis section describes the four types of LEDs on the x230 Series Switches: “POWER and FAULT LEDs” on page 22 “10/1000BASE-T

AT-x230-10GP and AT-x230-18GP Switches Installation Guide23Table 4 describes the POWER LED for the AT-x230-10GP and AT-x230-18GP switches.Figure 8 sho

Chapter 1: Overview24Table 5 describes the functions of the FAULT LED for the AT-x230-10GP and AT-x230-18GP switches.TABLE 5. AT-X230-10GP AND AT-X23

AT-x230-10GP and AT-x230-18GP Switches Installation Guide25FIGURE 9. AT-X230-10GP LINK/ACTIVITY/SPEED AND POE LEDSLTWERACT 10/100 LINK ACT PD ON PD ER

Chapter 1: Overview26Table 6 describes the AT-x230-10GP and AT-x230-18GP Link/Activity/Speed and PoE status LEDs.TABLE 6. AT-X230-10GP AND AT-X230-18G

AT-x230-10GP and AT-x230-18GP Switches Installation Guide27SFP LEDs The AT-x230-10GP and AT-x230-18GP switches have SFP Link/Activity LEDs on the fron

Chapter 1: Overview28Table 7 describes the functions of the SFP Link/Activity LEDs TABLE 7. SFP LINK/ACTIVITY LED FUNCTIONAL DESCRIPTIONSLED State Des

AT-x230-10GP and AT-x230-18GP Switches Installation Guide29The SD card LED indicates whether the SD card slot has a card inserted, or is reading or wr

iiTranslated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled Translated S

Chapter 1: Overview30ecofriendly buttonBy pressing the ecofriendly button you can conserve energy.When you press the ecofriendly button for 1 to 4 sec

AT-x230-10GP and AT-x230-18GP Switches Installation Guide31Power supplyEach switch has an internal power supply with a single AC power supply socket o

Chapter 1: Overview32FansBoth the AT-x230-10GP and AT-x230-18GP switches have one and two internal fans respectively. You cannot remove or replace the

AT-x230-10GP and AT-x230-18GP Switches Installation Guide33Chapter 2InstallationThis chapter contains the following sections: “Reviewing safety preca

Chapter 2: Installation34Reviewing safety precautionsPlease review the following safety precautions before you begin to install the chassis or any of

AT-x230-10GP and AT-x230-18GP Switches Installation Guide35All countries: Install product in accordance with local and National Electrical Codes.  E8

Chapter 2: Installation36Selecting a site for the switchObserve the following requirements when choosing a site for your switch: If you plan to insta

AT-x230-10GP and AT-x230-18GP Switches Installation Guide37Cable specificationsTable 9 contains the cable specifications for the twisted pair ports.No

Chapter 2: Installation38Unpacking the switch: AT-x230-10GPTo unpack the switch, perform the following procedure:1. Remove all of the components from

AT-x230-10GP and AT-x230-18GP Switches Installation Guide39Unpacking the switch: AT-x230-18GPTo unpack the switch, perform the following procedure:1.

AT-x230-10GP and AT-x230-18GP Switches Installation GuideiiiContentsPreface...

Chapter 2: Installation40Installing the switch on a table or a desktopYou can install AT-x230-10GP and AT-x230-18GP switches on a desktop, in a standa

AT-x230-10GP and AT-x230-18GP Switches Installation Guide41FIGURE 14. ATTACHING THE RUBBER FEET TO A SWITCHx230-10GPCONSOLERS-232SDFAULTPOWERSD1000 LI

Chapter 2: Installation42Installing an AT-x230-10GP switch in an equipment rackThese instructions show you how to install an AT-x230-10GP switch in an

AT-x230-10GP and AT-x230-18GP Switches Installation Guide434. Attach two rack mount brackets to the sides of the switch using the eight bracket screws

Chapter 2: Installation445. Mount the AT-x230-10GP switch in a 19-inch equipment rack using four equipment rack screws (supplied with the equipment ra

AT-x230-10GP and AT-x230-18GP Switches Installation Guide45Installing an AT-x230-18GP switch in an equipment rackThese instructions show you how to in

Chapter 2: Installation464. Attach two rack mount brackets to the sides of the switch using the sixbracket screws that come with the rack mount kit AT

AT-x230-10GP and AT-x230-18GP Switches Installation Guide475. Mount the AT-x230-18GP switch in a 19-inch equipment rack using four equipment rack scre

Chapter 2: Installation48Installing the switch on a wall using bracketsThese instructions show you how to install an AT-x230-10GP or AT-x230-18GP swit

AT-x230-10GP and AT-x230-18GP Switches Installation Guide494. While another person holds the switch at the wall location, secure it to the wall using

ContentsivChapter 3: Troubleshooting...

Chapter 2: Installation50Cabling the switchObserve the following guidelines when connecting twisted pair and fiber optic cables to the ports on the sw

AT-x230-10GP and AT-x230-18GP Switches Installation Guide51 The default speed setting for the ports is Auto-Negotiation. This setting is appropriate

Chapter 2: Installation52Powering on the switch To power on the AT-x230-10GP or AT-x230-18GP switch, perform the following procedure:1. Lift the power

AT-x230-10GP and AT-x230-18GP Switches Installation Guide533. Plug the other end of the power cord into a wall outlet.WarningPower cord is used as a d

Chapter 2: Installation54Starting a local management sessionThis procedure requires a terminal or a terminal emulator program and the management cable

AT-x230-10GP and AT-x230-18GP Switches Installation Guide55NoteThe port settings are for a DEC VT100 or ANSI terminal, or an equivalent terminal emula

Chapter 2: Installation56Monitoring the initialization processesIt takes about thirty seconds for the switch to initialize its management software pro

AT-x230-10GP and AT-x230-18GP Switches Installation Guide57FIGURE 27. SWITCH INITIALIZATION MESSAGES (CONTINUED)Starting base/portmapper...

Chapter 2: Installation58FIGURE 28. SWITCH INITIALIZATION MESSAGES (CONTINUED)Received event network.configuredawplus login:

AT-x230-10GP and AT-x230-18GP Switches Installation Guide59Installing optional SFP transceiversTo install an SFP transceiver, perform the following pr

vFiguresFigure 1: AT-x230-10GP packaging ...

Chapter 2: Installation603. Position the SFP transceiver with the label facing up.4. Gently slide the transceiver into the SFP slot until it clicks in

AT-x230-10GP and AT-x230-18GP Switches Installation Guide616. Eject SFP transceivers, as shown in Figure 32. First lower the SFP transceiver handle, t

Chapter 2: Installation62

AT-x230-10GP and AT-x230-18GP Switches Installation Guide63Chapter 3TroubleshootingThis chapter contains information on how to troubleshoot the switch

Chapter 3: Troubleshooting64 Try connecting another network device to the twisted pair port with a different cable. If the twisted pair port is able

AT-x230-10GP and AT-x230-18GP Switches Installation Guide65Problem 5: Network performance between a twisted pair port on the switch and a network devi

Chapter 3: Troubleshooting66

AT-x230-10GP and AT-x230-18GP Switches Installation Guide67Appendix ATechnical specificationsThis appendix describes the technical specifications of t

Appendix A: Technical specifications68Power specificationsInput supply voltage - 100-240 VAC, 50 - 60 Hz, 2.4A maximumElectrical safety and electromag

AT-x230-10GP and AT-x230-18GP Switches Installation Guide69Connectors and port pinoutsThis section lists the connectors and connector pinouts.Figure 3

List of Figuresvi

Appendix A: Technical specifications70Table 17 lists the RJ45 connector pins and their signals when a 1000BASE-T port is operating at 1000Mbps.TABLE 1

viiTablesTable 1. IEEE powered device classes ..........................