Allied-telesis AT-8203 Manual do Utilizador

AT-8202AT-8203 ATM and FDDI Uplink and Accelerator Cards For the FORMULA 8200™ Fast Ethernet Workgroup Switch Installation Guide PN 613-10660-00 Rev.

Verifying Your Uplink Package4 Verifying Your Uplink Package Your uplink card package consists of: ❑ This installation guide ❑ One of the following c

AT-8202 and AT-8203 Installation Guide5 Installing the Uplink Card Caution Prior to installing the uplink card, make sure you have successfully inst

Installing the Uplink Card6 4. Remove additional hardware, such as rackmounting brackets. Note If the switch is installed on the desktop, you need n

AT-8202 and AT-8203 Installation Guide7 Figure 5: Cover Plate Removal 7. Install the uplink card into the lower PCI slot (Figure 6).Ensure that t

Installing the Uplink Card8 8. Using the screw from Step 6, secure the uplink card to the chassis (Figure 7). Figure 7: Uplink Card Attachment to C

AT-8202 and AT-8203 Installation Guide9 Installing the Accelerator Card Before following these procedures, make sure the uplink card is already insta

Replacing the Chassis Top Cover10 Replacing the Chassis Top Cover 1. Slip the back of the cover over the back chassis rails, as shown in Figure 10. F

AT-8202 and AT-8203 Installation Guide11 Initializing the Switch 1. Connect a terminal to the switch’s console port so you can monitor the boot proce

Interpreting the LEDs12 Interpreting the LEDs The ATM uplink card has one link LED. If there is a valid link, the LED is solid green. If the uplink c

AT-8202 and AT-8203 Installation Guide13 Cabling Requirements for the FDDI Uplink Card The FDDI uplink card provides two dual SC connector ports (Fig

Copyright  1998 Allied Telesyn International Corp.All rights reserved. No part of this publication may be reproduced without prior written permiss

Cabling Requirements for the FDDI Uplink Card14DAS Cable ConnectionsFor a DAS configuration, connect Port A and Port B to their corresponding ports a

AT-8202 and AT-8203 Installation Guide15Where to Go From HereTo configure, operate, and monitor the switch, download the following guides from Allied

17Appendix AProduct Specifications for the FORMULA 8200 Switch With the Uplink CardNetwork Protocol Ethernet and Fast EthernetStandards Supported 802.

19Appendix BTechnical Support Fax OrderName___________________________________________________________________Company ________________________________

21Appendix CFORMULA 8200 Uplink Card Installation Guide FeedbackPlease tell us what additional information you would like to see discussed in the guid

23Appendix DWhere To Find UsFor Technical Support or ServiceLocation Phone FaxAmericasUnited States, Canada, Mexico, Central America, South America1 (

iii Electrical Safety and Installation Requirements STANDARDS : This product meets the following standards.RFI Emission EN55022 Class A WARNING : I

Where To Find Us24AustraliaLindfield, NSWTel: (612) 416-0619, Fax: (612) 416-9764CanadaRexdale, OntarioTel: (416) 675-6738, Fax: (416) 675-0057Richmond

Electrical Safety and Installation Requirements iv INSTALLATIONELECTRICAL—AUTO VOLTAGE ADJUSTMENT This product will automatically adjust to any volt

v Table of Contents Electrical Safety and Installation Requirements ...iii Uplink Card Installation ...

1 Uplink Card Installation This guide shows you how to install: ❑ One of the following uplink cards in the lower PCI slot of the FORMULA 8200 switch:

About the FDDI Uplink Card2 ❑ RFC 1577 Classical IP (CIP) and ARP over ATM ❑ ATM Forum’s User Network Interface (UNI) 3.0 or 3.1 signaling standard ❑

AT-8202 and AT-8203 Installation Guide3 As shown in Figure 2, the FDDI uplink allows workstations on Ethernet and Fast Ethernet networks to reach rem