Allied-telesis AT-PC232/POE Manual do Utilizador

613-001030 Rev. AFast EthernetMedia ConverterAT-PC232/POE◆Installation Guide

Tables10

AT-PC232/POE Media Converter Installation Guide11PrefaceThis guide provides the hardware installation instructions for your AT-PC232/POE Media Convert

Preface12Safety Symbols Used in this DocumentThis document uses the safety symbols defined in Table 1.Table 1. Safety SymbolsSymbol Meaning Descriptio

AT-PC232/POE Media Converter Installation Guide13Where to Find Web-based GuidesThe installation and user guides for all Allied Telesis products are av

Preface14Contacting Allied Telesis This section provides Allied Telesis contact information for technical support as well as sales or corporate inform

Section I: Basic Features 15Chapter 1OverviewThe AT-PC232/POE Media Converter is designed to extend the distance of your network by converting 10 /100

Chapter 1: Overview16IntroductionThe AT-PC232/POE Media Converter is a 10/100Base-TX copper to 100Base-FX fiber media converter is designed for both s

AT-PC232/POE Media Converter Installation Guide17Key FeaturesThe AT-PC232/POE Media Converter comes with the following features:❒ One 10/100Base-TX tw

Chapter 1: Overview1810/100Base-TX Twisted Pair PortThe 10/100Base-TX twisted pair port is described below:Type ofConnectorThe 10/100Base-TX twisted p

AT-PC232/POE Media Converter Installation Guide19Type of Cabling For 10 Mbps, the port requires Category 3 or better 100 ohm shielded or unshielded tw

Copyright © 2008 Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied T

Chapter 1: Overview20100Base-FX Fiber Optic PortThe AT-PC232/POE Media Converter features a single fiber optic port. Type ofConnectorThe fiber optic p

AT-PC232/POE Media Converter Installation Guide21Operating ModesThe AT-PC232/POE Media Converter supports these operating modes: “Link Test Mode,” n

Chapter 1: Overview22switches, one local and the other remote. Switch 1, the remote switch, is connected to port 1, the fiber optic port, on the media

AT-PC232/POE Media Converter Installation Guide23respond by pulsing the transmitter on the twisted pair port and flashing the port’s Link LED about on

Chapter 1: Overview24Power over EthernetThe twisted pair port on the AT-PC232/POE Media Converter features Power over Ethernet (PoE). PoE is a mechani

AT-PC232/POE Media Converter Installation Guide25Power Budgeting The AT-PC232/POE Media Converter can provide a maximum of 15.4 W of power on its twis

Chapter 1: Overview26LEDsThe LEDs on the AT-PC232/POE Media Converter, are shown in Figure 3 and are described in the following sections:❒ “Power LED”

AT-PC232/POE Media Converter Installation Guide2710/100Base-TXTwisted Pair PortLEDsthe LEDs for the 10/100Base-TX twisted pair port defined in Table 4

Chapter 1: Overview28Operating ModeLEDsThe three LEDs listed under MODE on the front panel display the operating mode of the media converter. The LEDs

AT-PC232/POE Media Converter Installation Guide29DIP SwitchesThe DIP switches are used to manually configure the operating characteristics of the 10/1

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class B, EN55022 Class B, EN61000-3-2, EN61000-

Chapter 1: Overview30A Few Basics about Ethernet SwitchingThe AT-PC232/POE Media Converter interconnects network devices, such as workstations, printe

AT-PC232/POE Media Converter Installation Guide31Network TopologiesStandaloneTopologyA standalone topology uses only one AT-PC232/POE Media Converter

Chapter 1: Overview32Back-to-BackTopologyIn some network configurations you may want to interconnect two AT-PC232/POE Media Converters in what is refe

AT-PC232/POE Media Converter Installation Guide33Chapter 2InstallationThis chapter explains how to install the AT-PC232/POE Media Converter and contai

Chapter 2: Installation34Verifying the Package ContentsMake sure the following items are included in your package. If any item is missing or damaged,

AT-PC232/POE Media Converter Installation Guide35Planning the InstallationObserve the following guidelines when planning the installation of your AT-P

Chapter 2: Installation36Selecting a Site When selecting a site for your AT-PC232/POE Media Converter, observe the following guidelines:❒ Select a sit

AT-PC232/POE Media Converter Installation Guide37Caution: Using controls, making adjustments to performance, or performing procedures other than those

Chapter 2: Installation38Warning: Operating Temperature. This product is designed for a maximum ambient temperature of 40° degrees C.  E7All Countrie

AT-PC232/POE Media Converter Installation Guide39Desktop InstallationInstall the AT-PC232/POE Media Converter on a desktop, perform the following proc

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Translated S

Chapter 2: Installation40Wall-Mount InstallationThe AT-PC232/POE Media Converter can be mounted vertically on a wall using the keyholes on the bottom

AT-PC232/POE Media Converter Installation Guide41Cabling the PortsPerform the following procedures to connect the network cables on the AT-PC232/POE M

Chapter 2: Installation42❒ Verify that you are using the appropriate type of fiber optic cabling.❒ Verify that the operating specifications of the con

AT-PC232/POE Media Converter Installation Guide43❒ You can use a straight-through or crossover twisted pair cable to connect any type of network devic

Chapter 2: Installation44Configuring the DIP SwitchesConfigure the DIP switches using the information in Table 10.When setting the DIP switches, consi

AT-PC232/POE Media Converter Installation Guide45Installing the Power Cord Retaining ClipPerform the following procedure to install the power cord ret

Chapter 2: Installation46Applying AC PowerTo apply AC power to the AT-PC232/POE Media Converter, perform the following procedure:1. Position the power

AT-PC232/POE Media Converter Installation Guide473. Lower the power cord retaining clip to secure the cord to the AT-PC232/POE Media Converter, as sho

Chapter 2: Installation48Verifying the InstallationThis procedure is used to verify the installation of the media converter. It determines whether or

Section II: Advanced Operations 49Chapter 3TroubleshootingHere are suggestions on how to troubleshoot the twisted pair port and the fiber optic port o

5ContentsPreface ...

Chapter 3: Troubleshooting50 Section II: Advanced Operations Verify that the operating specifications of the fiber optic port on the remote network d

AT-S63 Web Browser User’s Guide for AT-9400 StacksSection II: Advanced Operations 51 The two network devices are operating in different duplex modes.

Chapter 3: Troubleshooting52 Section II: Advanced Operations

53Appendix ATechnical SpecificationsPhysical Dimensions: W x D x H15.5 cm x 13.1 cm x 4.0 cm(6.10 in x 5.16 in x 1.58 in)Weight: .748 Kg (1.65 lb.)Tem

Chapter : Technical Specifications54Agency CertificationsRFI Emissions FCC Class B, EN55022 Class B, C-TICK, CEImmunity EN55024Electrical Safety EN609

AT-PC232/POE Media Converter Installation Guide55Table 12 lists the RJ-45 port pin signals when a twisted pair port is operating in the MDI-X configur

Chapter : Technical Specifications56

57Appendix BCleaning Fiber Optic ConnectorsThe fiber optic connector consists of a fiber optic plug and its adapter. The end of the fiber optic cable

Appendix B: Cleaning Fiber Optic Connectors58Using a Cartridge-Type CleanerFiber optic cartridge cleaners are available from many vendors and are typi

AT-LX44000 Multi-Protocol WDM Transport System Installation Guide592. Place the ferrule tip on the exposed cleaning surface and rub the ferrule in a d

Contents6Standalone Topology...

Appendix B: Cleaning Fiber Optic Connectors60Using a SwabSpecially treated swabs (stick cleaners) are available for cleaning inside connector adapters

AT-LX44000 Multi-Protocol WDM Transport System Installation Guide61To clean a recessed ferrule using a swab, perform the following procedure.1. Insert

Appendix B: Cleaning Fiber Optic Connectors62

7Figure 1. AT-PC232/POE Front Panel...

Figures8

9TablesTable 1. Safety Symbols ..............................