Allied-telesis AT-S97 Manual do Utilizador

613-000789 Rev. BManagement SoftwareAT-S85 and AT-S97◆Command Line InterfaceUser’s GuideAT-MCF2000 Media Converter SeriesVersion 1.4.0

Tables10

Chapter 6: Port and Module Commands100Privilege LevelsAdministrator, read-write, and read-only.General DescriptionThis command can display a variety o

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide101Description of the Chassis and Slot CommandTo view the current status of t

Chapter 6: Port and Module Commands102Table 5 lists the possible combinations of the port states for a channel in the Missing Link mode.The states for

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide103Description of the Chassis, Slot, and Channel CommandTo view the operating

Chapter 6: Port and Module Commands104Figure 15. SYSTEM SHOW INTERFACE Command - Chassis ID, Slot ID, and ChannelThe fields are defined here: Interfa

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide105Disabled - The port was disabled with SYSTEM SET PORT command. For informa

Chapter 6: Port and Module Commands106SYSTEM SHOW MODULESyntaxsystem show module id=chassis/slotParametersid Identifies a module. You can specify only

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide107DescriptionThis command displays status information about the media conver

Chapter 6: Port and Module Commands108Figure 17 illustrates the information for the management Module.Figure 17. SYSTEM SHOW MODULE Command for the Ma

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide109 Module Type - The model name. Power OK - A status of Yes signifies the

11PrefaceThe AT-S85 and AT-S97 Management Software programs are the operating systems for the AT-MCF2000 Media Converter Modules and the AT-MCF200M Ma

Chapter 6: Port and Module Commands110

111Chapter 7Network Time Protocol CommandsThis chapter contains the following sections: “Overview” on page 112 “NTP DISABLE” on page 114 “NTP ENABL

Chapter 7: Network Time Protocol Commands112OverviewThe AT-S97 Management Software comes with a Network Time Protocol (NTP) client for setting its int

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide113NTP SET on page 116 Specifies the IP address of the NTP server on the netw

Chapter 7: Network Time Protocol Commands114NTP DISABLESyntaxntp disableParametersNone.Privilege LevelsAdministrator and read-write.DescriptionThis co

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide115NTP ENABLESyntaxntp enableParametersNone.Privilege LevelsAdministrator and

Chapter 7: Network Time Protocol Commands116NTP SETSyntaxntp set server=ipaddressParametersserver Specifies the IP address of an NTP server.Privilege

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide117NTP SHOWSyntaxntp showParametersNone.Privilege LevelsAdministrator, read-w

Chapter 7: Network Time Protocol Commands118

119Chapter 8Event Log and Syslog Client CommandsThis chapter contains the following sections: “Overview” on page 120 “LOGGING CLEAR EVENTLOG” on pag

Preface12Document ConventionsThis document uses the following conventions:NoteNotes provide additional information.CautionCautions inform you that per

Chapter 8: Event Log and Syslog Client Commands120OverviewThe management, media converter, power supply, and fan modules generate event messages with

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide121 If the management module and syslog server are on different networks, th

Chapter 8: Event Log and Syslog Client Commands122LOGGING CLEAR EVENTLOGSyntaxlogging clear eventlogParametersNone.Privilege LevelAdministratorDescrip

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide123LOGGING DISABLE EVENTLOGSyntaxlogging disable eventlogParametersNone.Privi

Chapter 8: Event Log and Syslog Client Commands124LOGGING DISABLE SYSLOGSyntaxlogging disable syslogParametersNone.Privilege LevelsAdministrator and r

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide125LOGGING ENABLE EVENTLOGSyntaxlogging enable eventlogParametersNone.Privile

Chapter 8: Event Log and Syslog Client Commands126LOGGING ENABLE SYSLOGSyntaxlogging enable syslogParametersNone.Privilege LevelsAdministrator and rea

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide127LOGGING SET EVENTLOGSyntaxlogging set eventlog severity-level=critical|maj

Chapter 8: Event Log and Syslog Client Commands128DescriptionEvent messages are categorized into four severity levels of Critical, Major, Minor, and E

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide129LOGGING SET SYSLOGSyntaxlogging set syslog [host=ipaddress] [facility-code

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide13Where to Find Web-based GuidesThe installation and user guides for all Alli

Chapter 8: Event Log and Syslog Client Commands130LOGGING SHOWSyntaxlogging showParametersNone.Privilege LevelsAdministrator, read-write, and read-onl

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide131The fields in the Syslog Information section are: Status - The status of

Chapter 8: Event Log and Syslog Client Commands132LOGGING SHOW EVENTLOGSyntaxlogging show eventlogParametersNone.Privilege LevelsAdministrator, read-w

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide133The second part of an event’s status is its classification of report (RP)

Chapter 8: Event Log and Syslog Client Commands134Chassis and Slot IDs - The chassis ID and slot identifier of the source module of the message. The f

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide135Stacking Port Link A Stack port on the management module or the AT-MCF2000

Chapter 8: Event Log and Syslog Client Commands136Minor Level MessagesAuthentication Failure The management software denied access to an individual wh

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide137Port # Mode Set to <operating mode>A channel’s operating mode was ch

Chapter 8: Event Log and Syslog Client Commands138ExampleThis command displays the events in the event log:logging show event-logTFTP Session Open The

139Chapter 9Configuration File CommandsThis chapter contains the following sections: “Overview” on page 140 “CONFIG OVERWRITE” on page 152 “CONFIG

Preface14Contacting Allied TelesisThis section provides Allied Telesis contact information for technical support as well as sales and corporate inform

Chapter 9: Configuration File Commands140OverviewThe management and media converter modules store their parameter settings in a series of files called

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide1412. The media converter modules transmit a copy of their updated auxiliary

Chapter 9: Configuration File Commands142file copy srcfile=system://0/m/mcf_ai_traffic.cfgdstfile=system://0/m/mcf_24a_traffic.cfgThis command is desc

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide143When you remove a media converter module from a chassis and install it int

Chapter 9: Configuration File Commands144Editing a MasterConfigurationFileYou can edit the master configuration file on the management module with a t

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide145The section accepts the following AT-S97 Management Software commands: “S

Chapter 9: Configuration File Commands146Log ConfigurationThis section controls the event log and the syslog client.Figure 26. Log Configuration Secti

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide147Telnet and SSH ConfigurationThis section controls the Telnet and SSH serve

Chapter 9: Configuration File Commands148The section is prefaced with three header lines that identify the media converter module in the chassis contr

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide149Note the following guidelines when modifying the commands in this section:

15Chapter 1Starting a Command Line Management SessionThis chapter contains the following sections: “Management Overview” on page 16 “Starting a Loca

Chapter 9: Configuration File Commands150The name of a media converter module and the temperature threshold are controlled with the commands in the fi

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide151CONFIG SAVE on page 154 Updates the active configuration file with the lat

Chapter 9: Configuration File Commands152CONFIG OVERWRITESyntaxconfig overwrite enable|disable Id=c/sParametersenable Enables the configuration overwr

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide153CONFIG RUNSyntaxconfig runParametersNone.Privilege LevelsAdministrator and

Chapter 9: Configuration File Commands154CONFIG SAVESyntaxconfig saveParametersNone.Privilege LevelsAdministrator and read-write.DescriptionThis comma

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide155CONFIG SAVE FILESYSTEMSyntaxconfig save filesystem=system://chassis/slot/f

Chapter 9: Configuration File Commands156DescriptionThis command creates a new master configuration file with the current parameter settings of the mo

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide157CONFIG SETSyntaxconfig set filesystem=system://chassis/slot/filename.cfgPa

Chapter 9: Configuration File Commands158After designating an active master configuration file, do one of the following: To configure the modules in

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide159CONFIG SHOWSyntaxconfig showParametersNonePrivilege LevelsAdministrator, r

Chapter 1: Starting a Command Line Management Session16Management OverviewThe discussions in this section review the basic characteristics of the mana

Chapter 9: Configuration File Commands160Figure 35. CONFIG SHOW Command with a New Active Master FileIf you were to issue the CONFIG SAVE command at t

161Chapter 10File System CommandsThis chapter contains the following sections: “Overview” on page 162 “FILE COPY” on page 166 “FILE DELETE” on page

Chapter 10: File System Commands162OverviewThe following sections describe the functions of the commands in this chapter.Managing aModule’s FileSystem

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide163Uploading orDownloading aMasterConfigurationFileThe master configuration f

Chapter 10: File System Commands164management module communicates with the TFTP server through this port. The AT-MCF2000M Management Module must have

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide165“FILE DELETE” on page 169 Deletes the configuration files from the file sy

Chapter 10: File System Commands166FILE COPYSyntaxfile copy srcfile=system://chassis/slot/filename.cfgdstfile=system://chassis/slot/filename.cfgParame

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide167must be enclosed in double quotes. The filename must be unique from all ot

Chapter 10: File System Commands168NoteThe next example creates a copy of an auxiliary configuration file on a media converter module. This function s

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide169FILE DELETESyntaxfile delete filesystem=system://chassis/slot/filename.cfg

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide17AT-S97Command LineInterfaceThe AT-S97 Management Software has a command lin

Chapter 10: File System Commands170DescriptionThis command deletes files from the file systems of the management and media converter modules. You can

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide171This command deletes the configuration file “BM.cfg” from the media conver

Chapter 10: File System Commands172FILE DOWNLOADSyntax 1: Downloading the AT-S85 and AT-S97 Boot Loadersfile download srcfile=tftp://ipaddress/filenam

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide1730 or 31 The chassis ID numbers are limited to these values.slot Identifies

Chapter 10: File System Commands174General DescriptionThis command downloads new versions of the AT-S85 and AT-S97 boot loaders and management softwar

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide175Since this command uses the TFTP client on the management module, Allied T

Chapter 10: File System Commands176NoteA media converter module resets after receiving a new version of the AT-S85 Management Software, but immediatel

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide177The asterisk is used to indicate all slots in the chassis which means the

Chapter 10: File System Commands178This command downloads a new version of the AT-S97 Management Software onto the AT-MCF2000M Management Module in a

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide179FILE FASTDOWNLOADSyntaxfile fastdownload appblock|bootblock srcfile=tftp|x

Chapter 1: Starting a Command Line Management Session18The modules do not automatically update their configuration files and the active master configu

Chapter 10: File System Commands180configuration, and image files on to individual media converter modules. As a result, you have to specify the chass

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide181FILE RENAMESyntaxfile rename srcfile=system://chassis/slot/filename dstfil

Chapter 10: File System Commands182Privilege LevelsAdministrator and read-write.DescriptionThis command is used to rename master configuration files i

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide183This command renames the media converter configuration file “BM_0_1.cfg” t

Chapter 10: File System Commands184FILE SHOWSyntaxfile show filesystem=system://chassis/slot/filenameParameterssystem Specifies the chassis and module

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide185Figure 37. FILE SHOW CommandThe first four columns can be ignored. The rem

Chapter 10: File System Commands186NoteThe following examples illustrate how to display the files in the file system on a media converter module. This

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide187FILE UPLOADSyntax 1: Uploading a Configuration File to a TFTP Serverfile u

Chapter 10: File System Commands188dstfile=tftp Specifies the TFTP server to receive the file. This parameter uploads a configuration file from a mana

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide189Description of Syntax 2This command syntax is reserved for future versions

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide19Within a stack, you assign the management module on the master switch with

Chapter 10: File System Commands190

191Chapter 11Telnet Server CommandsThis chapter contains the following sections: “Overview” on page 192 “TELNET DISABLE” on page 194 “TELNET ENABLE

Chapter 11: Telnet Server Commands192OverviewThe commands in this chapter control the management module’s Telnet application protocol server, used for

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide193TELNET ENABLE on page 195Activates the Telnet application protocol server.

Chapter 11: Telnet Server Commands194TELNET DISABLESyntaxtelnet disableParametersNone.Privilege LevelsAdministrator and read-write.DescriptionThis com

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide195TELNET ENABLESyntaxtelnet enableParametersNone.Privilege LevelsAdministrat

Chapter 11: Telnet Server Commands196TELNET SHOWSyntaxtelnet showParametersNone.Privilege LevelsAdministrator, read-write, and read-only.DescriptionTh

197Chapter 12Secure Shell Server CommandsThis chapter contains the following sections: “Overview” on page 198 “SSH DISABLE” on page 200 “SSH ENABLE

Chapter 12: Secure Shell Server Commands198OverviewThe AT-S97 Management Software has a Secure Shell (SSH) application protocol server for remote mana

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide199 The management module must have an IP configuration. For instructions, r

Copyright © 2007 Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied T

Chapter 1: Starting a Command Line Management Session20Starting a Local Management SessionNoteLocal management sessions do not require an IP configura

Chapter 12: Secure Shell Server Commands200SSH DISABLESyntaxssh disableParametersNone.Privilege LevelsAdministrator and read-writeDescriptionThis comm

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide201SSH ENABLESyntaxssh enableParametersNone.Privilege LevelsAdministrator and

Chapter 12: Secure Shell Server Commands202SSH SHOWSyntaxssh showParametersNone.Privilege LevelsAdministrator, read-write and read-onlyDescriptionThis

203Chapter 13Manager Account CommandsThis chapter contains the following sections: “Overview” on page 204 “USER ADD” on page 206 “USER DELETE” on p

Chapter 13: Manager Account Commands204OverviewThe AT-S97 Management Software comes with one predefined manager account with a privilege level of admi

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide205USER SET on page 209 Modifies the password and privilege level of a manage

Chapter 13: Manager Account Commands206USER ADDSyntaxuser add username=name privilege=read|readwriteParametersusername Specifies a name between 1 and

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide207This command creates the new manager account “Eric Jones” with a privilege

Chapter 13: Manager Account Commands208USER DELETESyntaxuser delete username=nameParametersusername Specifies a name between 1 and 16 alphanumeric cha

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide209USER SETSyntaxuser set username=name password privilege=read|readwritePara

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide21NoteThe prompt “Hit any key to stop autoboot,” displayed on the console whe

Chapter 13: Manager Account Commands210This command changes the privilege level of the manager account “Smith” to read-write:user set username=Smith p

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide211USER SHOWSyntaxuser showParametersNone.Privilege LevelsAdministrator, read

Chapter 13: Manager Account Commands212

213Chapter 14Diagnostics CommandsThis chapter contains the following sections: “Overview” on page 214 “DIAGNOSTICS SHOW BOOTLOADER” on page 215 “DI

Chapter 14: Diagnostics Commands214OverviewThe diagnostics commands display manufacturing information which you may be asked to provide if you contact

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide215DIAGNOSTICS SHOW BOOTLOADERSyntaxdiagnostics show bootloaderParametersnone

Chapter 14: Diagnostics Commands216The fields are defined here: Slot ID: A slot in the chassis. Possible values are:– C: Indicates the chassis.– M: I

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide217DIAGNOSTICS SHOW CHASSISSyntaxdiagnostics show chassis id=chassis eepromPa

Chapter 14: Diagnostics Commands218NoteThe AT-MCF2000S Stacking Module is not displayed. Module Name - Indicates the name of the module. Refer to “SY

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide219DIAGNOSTICS SHOW MODULESyntaxdiagnostics show module id=chassis/slotParame

Chapter 1: Starting a Command Line Management Session22Starting a Remote Telnet or Secure Shell Management SessionReview the following guidelines befo

Chapter 14: Diagnostics Commands220Figure 43. DIAGNOSTICS SHOW MODULE CommandThe fields in the display are defined here: Name - The name of the modul

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide221ExamplesThis command displays information about the management module in a

Chapter 14: Diagnostics Commands222DIAGNOSTICS SHOW SOFTWARESyntaxdiagnostics show softwareParametersnonePrivilege LevelsAdministrator, read-write, an

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide223The fields are defined here: Slot ID: A slot in the chassis. Possible val

Chapter 14: Diagnostics Commands224

225Appendix AAT-S85 and AT-S97 Management Software Default SettingsThis appendix lists the factory default settings for the features in the AT-S85 and

Appendix A: AT-S85 and AT-S97 Management Software Default Settings226Configuration FileThe following table lists the default settings for the configur

AT-S85 and AT-97 Management Software Command Line Interface User’s Guide227Event LogThe following table lists the default settings for the event log.E

Appendix A: AT-S85 and AT-S97 Management Software Default Settings228IP ConfigurationThe following table lists the default settings for the IP configu

AT-S85 and AT-97 Management Software Command Line Interface User’s Guide229Manager AccountThe following table lists the default settings for the manag

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide23For information on the three manager privilege levels of the AT-S97 Managem

Appendix A: AT-S85 and AT-S97 Management Software Default Settings230Master Configuration FileThe following table lists the name of the default master

AT-S85 and AT-97 Management Software Command Line Interface User’s Guide231Network Time Protocol ClientThe following table lists the default settings

Appendix A: AT-S85 and AT-S97 Management Software Default Settings232RS-232 Terminal PortThe following table lists the default settings for the RS-232

AT-S85 and AT-97 Management Software Command Line Interface User’s Guide233Secure Shell ServerThe following table lists the SSH server default setting

Appendix A: AT-S85 and AT-S97 Management Software Default Settings234Syslog ClientThe following table lists the default settings for the syslog client

AT-S85 and AT-97 Management Software Command Line Interface User’s Guide235Telnet ServerThe following table lists the Telnet server default settings.T

Appendix A: AT-S85 and AT-S97 Management Software Default Settings236

237IndexNumerics10/100/1000Base-T Management portdisplaying status of 106setting 87Aactive master configuration filedescribed 142displaying name of 15

Index238SSH SHOW 202SYSTEM RESET CHASSIS 70SYSTEM RESET CLUSTER 72SYSTEM RESET MODULE 74SYSTEM SET ASYNCHRONOUS 56SYSTEM SET CHASSIS 57SYSTEM SET CLOC

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide239media converter ports 99Network Time Protocol (NTP) client 117Secure Shell

Chapter 1: Starting a Command Line Management Session24Quitting a Management SessionTo quit a management session, enter Exit at the command prompt. Yo

Index240media converter chassisdisplaying 94, 97, 99naming 57media converter modulescommand summary 68displaying 94, 97, 99, 106displaying file system

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide241enabling 126guidelines 120setting facility code 129setting server’s IP add

Index242

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide25Command Line Interface FeaturesThe command line interface supports the foll

Chapter 1: Starting a Command Line Management Session26Command FormattingThe following formatting conventions are used in this manual: screen text fo

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide27What to Configure FirstThis section has a few suggestions on what to config

Chapter 1: Starting a Command Line Management Session28NoteTo avoid possible compatibility problems between the management module and the media conver

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide29And, finally, filename.cfg is the filename for the new master configuration

3ContentsPreface ...

Chapter 1: Starting a Command Line Management Session30Assigning an IPConfigurationWill you be remotely managing the chassis with the Telnet or Secure

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide31Setting the Dateand TimeThe management module adds the date and time to the

Chapter 1: Starting a Command Line Management Session32Naming a Chassis Naming a chassis makes it easier for you to identify it in the management soft

33Chapter 2StackingThis chapter contains the following sections: “Overview” on page 34 “Required Modules” on page 35 “AT-S85 and AT-S97 Management

Chapter 2: Stacking34OverviewThe AT-MCF2000 chassis and the media converter modules interconnect Ethernet networking devices over large distances by t

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide35Required ModulesTo be part of a stack, the master chassis in the stack must

Chapter 2: Stacking36AT-S85 and AT-S97 Management Software VersionsTo create a stack, the management, stacking, and media converter modules require Ve

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide37Setting Up StackingWhen creating a stack, you need to designate a master ch

Chapter 2: Stacking38

39Chapter 3Basic CommandsThis chapter contains the following commands: “Question Mark ‘?’ Key” on page 40 “CLEAR” on page 41 “EXIT” on page 42 “HE

Contents4Chapter 4: IP Configuration Commands ...45

Chapter 3: Basic Commands40Question Mark ‘?’ KeySyntax?ParametersNone.Privilege LevelsAdministrator, read-write, and read-only.DescriptionEntering a q

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide41CLEARSyntaxclearParametersNone.Privilege LevelsAdministrator, read-write, a

Chapter 3: Basic Commands42EXITSyntaxexitParametersNone.Privilege LevelsAdministrator, read-write, and read-only.DescriptionThis command ends a manage

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide43HELPSyntaxhelpParametersNone.Privilege LevelsAdministrator, read-write, and

Chapter 3: Basic Commands44PINGSyntaxping ipaddressParameteripaddress Specifies the IP address of the device to ping.Privilege LevelsAdministrator and

45Chapter 4IP Configuration CommandsThis chapter contains the following sections: “Overview” on page 46 “IP DHCP DISABLE” on page 48 “IP DHCP ENABL

Chapter 4: IP Configuration Commands46OverviewThe IP commands assign an IP configuration to the AT-MCF2000M Management Module consisting of an IP addr

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide47CommandSummaryTable 1 summarizes the IP configuration commands.Table 1. IP

Chapter 4: IP Configuration Commands48IP DHCP DISABLESyntaxip dhcp disableParametersNone.Privilege LevelsAdministrator and read-write.DescriptionThis

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide49IP DHCP ENABLESyntaxip dhcp enableParametersNone.Privilege LevelsAdministra

AT-S85 and AT-97 Management Software Command Line Interface User’s Guide5LOGGING SET SYSLOG ...

Chapter 4: IP Configuration Commands50IP SETSyntaxip set ip-address=ipaddress subnetmask=mask default-gateway=ipaddressParametersip-address Specifies

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide51This command assigns the default gateway address 149.44.55.22 to the manage

Chapter 4: IP Configuration Commands52IP SHOWSyntaxip showParametersNone.Privilege LevelsAdministrator, read-write, and read-only.DescriptionThis comm

53Chapter 5General System CommandsThis chapter contains the following sections: “Overview” on page 54 “SYSTEM SET ASYNCHRONOUS” on page 56 “SYSTEM

Chapter 5: General System Commands54OverviewThe system commands are divided into two groups in this manual. The first set of commands, described in th

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide55“SYSTEM SHOW CONSOLE” on page 65Displays the console timeout parameter.“SYS

Chapter 5: General System Commands56SYSTEM SET ASYNCHRONOUSSyntaxsystem set asynchronous baudrate=2400|4800|9600|19200|115200Parametersbaudrate Sets t

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide57SYSTEM SET CHASSISSyntaxsystem set chassis id=chassis name=nameParametersid

Chapter 5: General System Commands58SYSTEM SET CLOCKSyntaxsystem set clock date=mm/dd/yyyy time=hh:mm:ssParametersdate Specifies the current date in m

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide59SYSTEM SET CONSOLESyntaxsystem set console timeout=valueParametertimeout Sp

Contents6Chapter 14: Diagnostics Commands ...21

Chapter 5: General System Commands60SYSTEM SET CONTACTSyntaxsystem set contact=contactParametercontact Specifies the name of the network administrator

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide61SYSTEM SET HOSTNAMESyntaxsystem set hostname=nameParameterhostname Specifie

Chapter 5: General System Commands62SYSTEM SET LOCATIONSyntaxsystem set location=locationParameterslocation Specifies a location of up to 25 alphanume

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide63SYSTEM SHOW ASYNCHRONOUSSyntaxsystem show asynchronousParametersNone.Privil

Chapter 5: General System Commands64SYSTEM SHOW CLOCKSyntaxsystem show clockParametersNonePrivilege LevelsAdministrator, read-write, and read-onlyDesc

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide65SYSTEM SHOW CONSOLESyntaxsystem show consoleParametersNone.Privilege Levels

Chapter 5: General System Commands66SYSTEM SHOW INFOSyntaxsystem show infoParametersNone.Privilege LevelsAdministrator, read-write, and read-only.Desc

67Chapter 6Port and Module CommandsThis chapter contains the following sections: “Overview” on page 68 “SYSTEM RESET CHASSIS” on page 70 “SYSTEM RE

Chapter 6: Port and Module Commands68OverviewThe system commands are divided into two groups in this manual. The first group of commands, described in

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide69NoteThe SYSTEM RESET CHASSIS, SYSTEM RESET CLUSTER, and SYSTEM RESET MODULE

7Figure 1: Chassis ID Jumper on the AT-MCF2000M Management Module...18Figure 2:

Chapter 6: Port and Module Commands70SYSTEM RESET CHASSISSyntaxsystem reset chassis id=chassisParametersid Identifies the ID number of the chassis to

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide71Note the following before performing this command: The command does not af

Chapter 6: Port and Module Commands72SYSTEM RESET CLUSTERSyntaxsystem reset clusterParametersNone.Privilege LevelAdministrator.DescriptionThis command

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide73After performing this command, you must do the following before you can sav

Chapter 6: Port and Module Commands74SYSTEM RESET MODULESyntaxsystem reset module id=chassis/slotParametersid Identifies the media converter module or

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide75NoteResetting a media converter module may result in the loss of some netwo

Chapter 6: Port and Module Commands76This command resets the AT-MCF2000M Management Module installed:system reset module id=0/mThis command resets the

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide77SYSTEM SET INTERFACESyntaxsystem set interface id=chassis/slot[/channel]opm

Chapter 6: Port and Module Commands78opmode Specifies the operating mode for the channel. Available settings are:link-test Specifies the Link Test mod

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide79ports, it replicates the loss on the companion port in the same channel by

Figures8

Chapter 6: Port and Module Commands80a link, then their Link LEDs will both be off and their status in the SYSTEM SHOW INTERFACE command will be Offli

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide81The operating mode functions the same if the failure starts on the twisted

Chapter 6: Port and Module Commands82Operating Mode GuidelinesThe following guidelines apply to using the channel operating modes: The channels on a

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide83SYSTEM SET INTERFACE PORTNAMESyntaxsystem set interface id=c|b|pp portname=

Chapter 6: Port and Module Commands84SYSTEM SET MODULESyntaxsystem set module id=chassis/slot name=nametemperature-threshold=valueParametersid Specifi

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide85SHOW INTERFACE” on page 99, “SYSTEM SHOW CHASSIS” on page 94 or “SYSTEM SHO

Chapter 6: Port and Module Commands86ExamplesThis command assigns the name “mm vata” to a management module in a chassis with the chassis ID of 0:syst

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide87SYSTEM SET PORTSyntaxsystem set port id=c/m|b/[pp]/[port]port-state=disable

Chapter 6: Port and Module Commands88port Specifies the letter of a port in a channel on a media converter module. Possible values are:a Specifies a t

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide891000 Sets the speed of the port to 1000 Mbps. This setting is applicable to

9Table 1: IP Configuration Commands ...

Chapter 6: Port and Module Commands90This command can also set the operating parameters of the 10/100/1000Base-T Management port on the management mod

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide91connected to the ports, should be using the same duplex mode. A media conve

Chapter 6: Port and Module Commands92ExamplesThis command disables Auto-Negotiation of the twisted pair port in channel 5 of a media converter module

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide93This command disables all the twisted pair ports in the media converter mod

Chapter 6: Port and Module Commands94SYSTEM SHOW CHASSISSyntaxsystem show chassis id=chassisParameterschassis Identifies the ID number of the chassis.

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide95An example of the information is shown in Figure 11.Figure 11. SYSTEM SHOW

Chapter 6: Port and Module Commands96ExampleThe following command displays information about a chassis with an ID number of 0: system show chassis id=

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide97SYSTEM SHOW CLUSTERSyntaxsystem show clusterParametersNone.Privilege Levels

Chapter 6: Port and Module Commands98Figure 12. SYSTEM SHOW CLUSTER CommandExamplesystem show clusterChassis Chassis Chassis MAC MasterID Name Type Ad

AT-S85 and AT-S97 Management Software Command Line Interface User’s Guide99SYSTEM SHOW INTERFACESyntax - Chassis Onlysystem show interface id=chassisS