Allied-telesis AR400 series Manual do Utilizador descarregar pdf (Página 1)

C613-16030-00 REV B

www.alliedtelesis.com

How To |

Introduction

Ideally, setting up an ISDN connection is very much a straightforward process:

z Connect the router to the ISDN network interface.

z Configure ISDN call definitions on the router. See How To Configure ISDN Calls On Allied

Telesis Routers, available from www.alliedtelesis.com/resources/literature/howto.aspx.

z Send traffic.

However, for one reason or another, there are occasions when the setup process is not as

smooth as it should be.

So if you have set up your router to communicate over ISDN, but the setup does not appear

to be working, this How To Note contains some steps you can take to try and resolve the

problem.

Which products does it apply to?

This configuration applies to the following Allied Telesis routers and switches, when a BRI or

PRI interface is installed in the base unit or through a PIC:

z AR300 series routers

z AR400 series routers

z AR700 series routers

z Rapier series switches

z Rapier i series switches

Related How To Notes

You also may find the following How To Notes useful:

How To Configure ISDN Calls On Allied Telesis Routers

z How To Configure Common ISDN Access Concentration With The Firewall

How To Notes are available from www.alliedtelesis.com/resources/literature/howto.aspx.

Troubleshoot ISDN Connections

1 2 3 4 5 6 7 8

Resumo do Conteúdo

Página 1 - Troubleshoot ISDN Connections

C613-16030-00 REV Bwww.alliedtelesis.comHow To |IntroductionIdeally, setting up an ISDN connection is very much a straightforward process: z Connect t

Página 2 - How to troubleshoot ISDN

2How to troubleshoot ISDNStep 1: Is the router communicating with the ISDN network at the signalling level?When the router is connected to the ISDN ne

Página 3

3If the interface is not activated, the reason could be one of the following: 1. The interface has been put into NT mode. On the AT-AR041 and AT-AR042

Página 4

43. The cable connecting the router to the ISDN network or NTI is faulty. Try a different cable.4. There is a fault in the ISDN network or the NT1. If

Página 5

5If the LAPD is not alive, the reason could be one of the following: 1. The TEI mode has been set incorrectly. On a Basic Rate interface, the TEI mode

Página 6 - The Cause column

6When it comes to diagnosing an ISDN connection, the two most important columns in this table are Duration and Cause. The Duration columnThe Duration

Página 7

7Also, a call that is closed due to PAP/CHAP authentication failure has a cause code of 16 because the call worked fine at the ISDN level, and was clo

Página 8 - Call has no user attached

USA Headquar ters | 19800 Nor th Cr eek Parkwa y | Suite 200 | Bothell | WA 98011 | USA | T: +1 800 424 4284 | F: +1 425 481 3895

Comentários a estes Manuais

Sem comentários

Allied-telesis AR400 series Manual do Utilizador Página 1

Consulte online ou descarregue Manual do Utilizador para Hardware Allied-telesis AR400 series. Allied Telesis AR400 series User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Allied-telesis AR400 series Manual do Utilizador Página 1

Consulte online ou descarregue Manual do Utilizador para Hardware Allied-telesis AR400 series. Allied Telesis AR400 series User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Allied-telesis AR400 series