Allied Telesis AT-GS924M Guia de Instalação

613-001986 Rev AAT-GS908MAT-GS916MAT-GS924MGigabit Ethernet SwitchesInstallation Guide

List of Tables10

11PrefaceThis guide contains the installation instructions for the AT-GS908M, AT-GS916M, and AT-GS924M Gigabit Ethernet Switches. This preface contain

12Symbol ConventionsThis document uses the following conventions:NoteNotes provide additional information.CautionCautions inform you that performing o

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide13Contacting Allied TelesisIf you need assistance with this product, you may contact Al

14

15Chapter 1OverviewThis chapter provides descriptions of the AT-GS908M, AT-GS916M, and AT-GS924M Layer 2 Gigabit Ethernet Switches and contains the fo

Chapter 1: Overview16FeaturesHere are the hardware features of the AT-GS900M Series Gigabit Ethernet Switches.Twisted-PairPortsHere are the basic feat

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide17LEDs The following lists the switch LEDs: Power LED; refer to “POWER LED” on page 23

Chapter 1: Overview18Front and Back PanelsFigure 1 illustrates the front panels of the AT-GS908M, AT-GS916M, and AT-GS924M Gigabit Ethernet Switches.F

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide19Figure 2 illustrates the back panels of the AT-GS908M, AT-GS916M, and AT-GS924M switc

Copyright © 2014 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Chapter 1: Overview20Management SoftwareThe switches are shipped with the ATPro management software pre-installed. The software provides a web-browser

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide21Twisted-Pair PortsThe AT-GS908M, AT-GS916M, and AT-GS924M Layer 2 Gigabit Ethernet Sw

Chapter 1: Overview22Combo PortsThe AT-GS916M Switch has two combo ports, and the AT-GS924M Switch has four combo ports. Each combo port consists of o

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide23LEDsThere are four types of LEDs on the AT-GS900M Series switches: “STATUS LEDs” “M

Chapter 1: Overview24FAULT LEDThe FAULT LED reports any conditions on the switch that are not normal.Table 3 describes the states of the FAULT LED.STA

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide25Figure 4. MODE LEDsTable 5 describes the MODE LEDs for the AT-GS900M Series switches.

Chapter 1: Overview26. SFP Slot LEDs The SFP Slot LEDs report the link activity status of each SFP slot.The AT-GS924M SFP Slot LEDs are shown in Figur

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide27. Table 7. SFP Slot LED Functional DescriptionsLED State DescriptionLink/ActivityOff

Chapter 1: Overview28Reset ButtonPressing the Reset button resets your switch.The Reset button is located next to the STATUS LEDs. See Figure 3 on pag

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide29Mode ButtonUse the Mode button to select whether the Port LEDs display the Link Activ

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions FCC Class A, EN55022 Class A, EN61000-3-2, EN61000-

Chapter 1: Overview30Power SupplyEach switch has an internal power supply with a single AC power supply socket on the back panel. To power the switch

31Chapter 2InstallationThis chapter contains the following sections: “Reviewing Safety Precautions” on page 32 “Selecting a Site for the Switch” on

Chapter 2: Installation32Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the chassis or any of

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide33CautionAir vents must not be blocked and must have free access to the room ambient ai

Chapter 2: Installation34WarningReliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply conne

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide35Selecting a Site for the SwitchObserve the following requirements when choosing a sit

Chapter 2: Installation36Cable SpecificationsTable 8 contains the cable specifications for the twisted-pair ports.NoteThe twisted-pair ports on the sw

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide37Unpacking the SwitchTo unpack the switch, perform the following procedure:1. Remove a

Chapter 2: Installation38Figure 7. Shipping Package ContentsRetaining clipManagement cableFour rubber feet One regional AC power cordOne, two, or four

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide39Installing the Power Cord Retaining ClipPerform the following procedure to install th

4Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled Translated Sa

Chapter 2: Installation40Installing the Switch on a Desktop or TableYou may install the switches on a desktop or table, or in a standard 19-inch equip

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide41Installing the Switch in an Equipment RackNoteThe AT-GS916M and AT-GS924M rack mounti

Chapter 2: Installation423. Mount the switch in a standard 19-inch equipment rack using four equipment rack screws (not provided with the switch). See

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide43Installing SFP TransceiversTo install an SFP transceiver, perform the following proce

Chapter 2: Installation444. Slide the transceiver into the SFP slot until it clicks into place. See Figure 13.Figure 13. Inserting the SFP5. Verify th

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide457. Go to “Cabling the Switch” on page 46.

Chapter 2: Installation46Cabling the SwitchObserve the following guidelines when connecting twisted-pair and fiber-optic cables to the ports on the sw

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide47Powering On the SwitchTo power on the switch, perform the following procedure:1. Lift

Chapter 2: Installation484. Verify that the POWER LED is green. If the LED is OFF, see Chapter 3, “Troubleshooting” on page 49.The switch is now power

49Chapter 3TroubleshootingThis chapter contains information on how to troubleshoot the switch if a problem occurs.NoteFor further assistance, please c

5ContentsPreface ...

Chapter 3: Troubleshooting50 Verify that you are using the appropriate category of twisted-pair cable: Category 3 or better for 10 Mbps operation and

51Appendix ATechnical SpecificationsThis appendix contains the following specifications: “Physical Specifications” “Environmental Specifications” on

Appendix A: Technical Specifications52Environmental SpecificationsPower SpecificationsInput Supply Voltage - 100-240 VAC, 50 - 60 HzSafety and Electro

AT-GS908M, AT-GS916M, and AT-GS924M Switches Installation Guide53Connectors and Port PinoutsThis section lists the connectors and connector pinouts.Fi

Appendix A: Technical Specifications54Table 16 lists the RJ-45 connector pins and their signals when a 1000Base-T port is operating at 1000 Mbps.Table

Contents6

7Figure 1: AT-GS908M, AT-GS916M, and AT-GS924M Front Panels... 18Figure

List of Figures8

9Table 1. Combo Ports ...............................