Allied Telesis AT-A16 Manual do Utilizador

i Allied Telesyn InternationalEthernet Network Adapter For ISA Bus Computers and IEEE 802.3 Compliant LANs User Manual AT-1700T Plus for Twisted Pair

6 Chapter 3 A Simplified Hardware/Software Installation Procedure Two Installation Contexts Installation of your ATI network adapter card may be perf

A Simplified Hardware/Software Installation 7 Installing the Adapter Card Refer to the computer’s manual for information on installing card-cage acce

AT-17008 Installing the Workstation Software 1. Turn your computer on.2. Install the ATI CardAssistant diskette in a floppy disk drive, typically dri

A Simplified Hardware/Software Installation 9 network software is able to communicate with the network, you have successfully installed and configure

10 Chapter 4 The AT-1700 Network Card The ATI AT-1700 16-bit Ethernet Adapter Card provides a PC access to an Ethernet Local Area Network (LAN) for

The AT-1700 Network Card11 10BASE-T, 10BASE2, 10BASE5 or 10BASE-FL Choices The AT-1700T, BT, AT and FT versions all have an RJ45 receptacle for conne

12 Chapter 5 Installation OS/Environment-Specific Installation Information Accurate and current network hardware and software installation informati

Installation13 1. Check system requirements on page 1.2. Consult instructions for adding peripherals in your computer’s instruction manual.3. Check I

AT-170014 The card works in either a 16-bit ISA slot or an EISA slot. If you are not using an EISA slot, skip step 3.3. Run your computer’s EISA con

Installation15 Launching the CardAssistant program requires that the card is present. If you have a driver running, you will not be allowed to open t

AT-1700ii Warranty: Your Allied Telesyn International CentreCOM ™ Ethernet Network Adapter has a lifetime warranty. Refer to the warranty card suppl

AT-170016 Working with CardAssistant menus You can use either the keyboard or mouse to: ❑ Make menu selections ❑ Change parameter settings ❑ Save or

Installation17 2. Choose “Configure I/O Parameters” or “Auto Configure” from the main menu. “Configure I/O Parameters” displays the card’s current se

AT-170018 Running Diagnostic Checks If you have not cycled power and rebooted the computer since changing the configuration, diagnostics will run ag

Installation19 The drivers must not be loaded when the diagnostics routines are run, or the diagnostics results will be inaccurate. Installing More

AT-170020 Parameters may be combined on the command line.Here are sample command lines for differing requirements: setup17 0x300 /I15 /UTP /Bc8

Installation21 Reconfiguring a Previously Installed Card If the card is working properly but you wish to reconfigure some of the I/O parameters, see

22 Chapter 6 Network Adapter Card Drivers Because user network environments are numerous, differing in network-management software, operating systems

Network Adapter Card Drivers23 Drivers for Servers If you are installing the card in a server, bridge, router or brouter, refer to Table 4. NOTE 1

AT-170024 Driver Installation The procedures for installing, binding or merging these drivers with the network software vary with the operating syste

Network Adapter Card Drivers25 3. Choose the appropriate driver from the menu choices. Following the instructions on the screen, copy the driver to a

iii Contents: 1 Square One ... 1What You Get From

AT-170026 When you install an ATI network adapter card, and invoke the installation program setup17.exe on the ATI distribution diskette, all the f

Network Adapter Card Drivers27 5. The batch file you use to get on the network must contain these lines in the following order : LSL AT17ODI

AT-170028 Support for Multiple Adapter Cards You can have up to four AT-1700 adapter cards in a single computer (workstation or server). Each needs i

29 Chapter 7 Cabling For complete rules of cabling and for information useful in planning network configurations, see ISO/IEEE Publication 8802-3. Th

AT-170030 The identification problem is exaggerated by the fact that some suppliers have sold purportedly data-quality cables manufactured with voice

Cabling31 The six common modular cable specifications and their applicability to 10BASE-T network use are shown in Table 5, and cable schematics are

AT-170032 Figure 2: `Usable and Unusable 10BASE-T Cable Figure 3 shows where to locate pin 1. Figure 3: Pin 1 Orientation on an RJ45 Connector1 TD+

Cabling33 10BASE2 RG58/BNC Cabling In addition to an RJ45 connector, the AT-1700BT has a BNC connector for 10BASE2 standard thin Ethernet RG58 coaxia

AT-170034 10BASE-FL/FOIRL (Optical Fiber) Connection The AT-1700FT provides both an RJ45 for 10BASE-T Ethernet and ST-type transmit and receive conne

Cabling35 10BASE5 (AUI) Connection The AT-1700AT offers both an RJ45 and an AUI port. (See Figure 7 and Figure 8.) Figure 7: AUI Connector for Thick

AT-1700iv 7 Cabling ... 29Important 10BASE

AT-170036 If a transceiver is installed, care must be taken with the setting of the heartbeat/SQE switch. Unless the transceiver is installed on a de

37 Chapter 8 Troubleshooting A network is a complex combination of hardware and software, all of which must function for data communication to work.

AT-170038 Experiment with Possible Solutions The first rule of troubleshooting is to isolate the problem. As you experiment, only vary one factor at

Troubleshooting39 failure or a slot failure. You may need to reconfigure the adapter card or the other device to avoid the conflict.Only one device i

AT-170040 5. Update the adapter card driver for the new settings. (See your network software manual.) Table 8: Some Typical Device Uses of Bus Resou

Troubleshooting41 To determine base I/O address and interrupt If the CardAssistant program does not detect the presence of the card, the address may

AT-170042 call the support office for your region. See “Technical Support Telephone Numbers” on page 45. The voice and fax telephone numbers for tech

Troubleshooting43 Technical Support Fax Order Name__________________________________________________Address _____________________City________________

AT-170044 Incident Summary ________________________________________Conditions (List the steps that led up to the problem.)___________________________

Troubleshooting45 Table 9: Technical Support Telephone Numbers Asia Singapore, Taiwan, Thailand, Malaysia, Indonesia, Korea, Hong Kong, Philippines

1 Chapter 1 Square One What You Get From Us When opening this ATI product, make sure that the package you have received is complete and in good condi

AT-170046 Hardware Warranty and Software License Agreement Allied Telesyn International Lifetime Adapter Card Warranty Allied Telesyn International (

47 Nach absechlossener Reparatur oder dem vollständigen Ersatz eines Artikels werden die Produkte an den Kunden zurückgeschickt und zwar einer von AT

AT-170048 2. License. Allied Telesyn International and its licensors retain ownership of the Software. For Software delivered on floppy disk, you own

49 11. General. This License will be governed by the laws of the United States and of California, as applied to agreements entered into by California

AT-170050 Adapter Card Revision History Revision Description Date Added AUI port option 8/93Converted to high/low interrupt-request (IRQ) options8/93

51 Adapter Card Manual Feedback We would like you to tell us the type of additional information you would like to see in the manual. If there are top

AT-17002 ❑ 512K of available RAM when running ATI CardAssistant setup/diagnostics software ❑ A free 32-byte block of I/O at 240h, 260h, 280h, 2A0h, 3

3 Chapter 2 Networking Overview for the New User/Installer More and more often, non-technical computer users are called on to install new software a

AT-17004 Your network software also requires some additional software, a special “interpreter”, which allows your network software to talk to the par

Networking Overview for the New User/Installer5 In summary, your networked PC will function properly on the network if the following are true. —You h