Allied-telesis AT-TQ2450 Manual do Utilizador

613-001820 Rev. AAT-TQ2450Enterprise-class Wireless Access Pointwith IEEE802.11a/b/g/n Dual RadioInstallation Guide

List of Figures10

11Table 1. Rear Panel Components ...

List of Tables12

13PrefaceThis guide contains the hardware installation instructions for the AT-TQ2450 Wireless Access Point. This preface contains the following secti

Preface14Safety Symbols Used in this DocumentThis document uses the following conventions.NoteNotes provide additional information.CautionCautions inf

AT-TQ2450 Wireless Access Point Installation Guide15Contacting Allied TelesisIf you need assistance with this product, you may contact Allied Telesis

Preface16

17Chapter 1OverviewThis chapter describes the hardware components of the AT-TQ2450 Wireless Access Point. This chapter contains the following sections

Chapter 1: Overview18FeaturesThe main features of the product are listed here: Independent 2.4 and 5 GHz radios IEEE 802.11a/b/g IEEE 802.11n 2x2 M

AT-TQ2450 Wireless Access Point Installation Guide19Front and Rear PanelsThe front and rear panels of the unit are illustrated in Figure 1 and Figure

Copyright  2013 Allied Telesis, Inc.All rights reserved.This product includes software licensed under the BSD License. As such, the following languag

Chapter 1: Overview20Table 1. Rear Panel ComponentsField DescriptionConsole Port The Console Port is for manufacturing purposes only.Rest Button The R

AT-TQ2450 Wireless Access Point Installation Guide212.4 and 5 GHz Antenna ConnectorsThe access point has two independent radios that operate at 2.4 an

Chapter 1: Overview22LAN PortThe LAN port is used to connect the device to your Local Area Network (LAN), typically through an Ethernet switch.Power o

AT-TQ2450 Wireless Access Point Installation Guide23Automatic MDIXDetectionThe 10/100/1000 Mbps twisted-pair port is IEEE 802.3ab compliant and featur

Chapter 1: Overview24LEDsThe LEDs on the AT-TQ2450 Access Port are described in Table 3.Table 3. LEDs on the AT-TQ2450 Access PointLED State Descrip

AT-TQ2450 Wireless Access Point Installation Guide25Reset ButtonThe Reset button on the rear panel is used to return the parameter settings of the uni

Chapter 1: Overview26

27Chapter 2Installing the Access PointThis chapter describes how to install the AT-TQ2450 Wireless Access Point. This chapter contains the following s

Chapter 2: Installing the Access Point28Reviewing Safety PrecautionsPlease review the following safety precautions before you begin to install the acc

AT-TQ2450 Wireless Access Point Installation Guide29WarningOperating Temperature. This product is designed for a maximum ambient temperature of 40° de

3Electrical Safety and Emissions StandardsThis product meets the following standards.Federal Communications Commission Interference StatementDeclarati

Chapter 2: Installing the Access Point30Unpacking the AT-TQ2450 Access PointAs you unpack the access point, check the shipping container for the compo

AT-TQ2450 Wireless Access Point Installation Guide31Figure 5. Power Adapter with One North American Power CordFigure 6. Power Adapter with Four Region

Chapter 2: Installing the Access Point32Do one of the following: To install the unit on a table, go to “Installing the Access Point on a Table” on pa

AT-TQ2450 Wireless Access Point Installation Guide33Installing the Access Point on a TableTo install the access point on a table, perform the followin

Chapter 2: Installing the Access Point34Figure 9. Attaching the Network Cable to the LAN Port4. Connect the other end of the network cable to a port o

AT-TQ2450 Wireless Access Point Installation Guide356. Connect the DC cable on the AC/DC adapter to the 12VDC connector on the access point. Refer to

Chapter 2: Installing the Access Point36Figure 12. Securing the DC Power Cord to the Access Point with the Tie Wrap8. Connect the AC plug on the power

AT-TQ2450 Wireless Access Point Installation Guide37Installing the Access Point on a Wall of Ceiling with the AT-BRKT-J26 BracketThis section contains

Chapter 2: Installing the Access Point38Figure 14. Flange on the Bottom Panel of the AT-BRKT-J26 Bracket You should verify that the wall or ceiling m

AT-TQ2450 Wireless Access Point Installation Guide39Figure 15. Screw Holes on the Bottom Panel of the AT-BRKT-J26 Bracket The holes have a diameter o

4NoteFor additional regulatory statements, refer to Appendix B, ”Regulatory Statements” on page 63.Safety and Electromagnetic Emissions CertificatesEu

Chapter 2: Installing the Access Point40Attaching theBottom Panel tothe Wall orCeilingTo attach the bottom panel of the bracket to the wall or ceiling

AT-TQ2450 Wireless Access Point Installation Guide414. Have someone hold the panel at the selected wall or ceiling location while you secure it to wit

Chapter 2: Installing the Access Point42Figure 19. Rear Panel Upside Down2. Locate the two screw holes on the rear panel. The holes are used to secure

AT-TQ2450 Wireless Access Point Installation Guide43Figure 21. Attaching the Top Panel to the Access Point4. Place the top panel and access point over

Chapter 2: Installing the Access Point44Figure 22. Attaching the Top Panel and Access Point to the Bottom PanelAnchor Pins

AT-TQ2450 Wireless Access Point Installation Guide455. Secure the top panel and access point to the bottom panel by tightening the two captive screws

Chapter 2: Installing the Access Point46Figure 24. Installing the AntennasCautionDo not attach the antennas when the access point is power on. Doing s

AT-TQ2450 Wireless Access Point Installation Guide47Figure 25. Attaching the LAN Cable8. Connect the other end of the network cable to a port on an Et

Chapter 2: Installing the Access Point4810. Connect the DC cable on the AC/DC adapter to the 12VDC connector on the access point. Refer to Figure 27.F

AT-TQ2450 Wireless Access Point Installation Guide49Figure 28. Securing the DC Power Cord to the AT-BRKT-J26 Bracket with the Tie Wrap12. Connect the

5Translated Safety StatementsImportant: The  indicates that a translation of the safety statement is available in a PDF document titled “Translated S

Chapter 2: Installing the Access Point50Installing Anti-theft DevicesThe bracket has three holes for anti-theft devices. You may want to install one o

AT-TQ2450 Wireless Access Point Installation Guide51Starting the Initial Management Session on the Access PointWhen you power on the access point for

Chapter 2: Installing the Access Point52Starting theInitialManagementSession with aDirectConnectionTo start the management session with a direct Ether

AT-TQ2450 Wireless Access Point Installation Guide53Starting theInitialManagementSession without aDHCP ServerThis procedure explains how to start the

Chapter 2: Installing the Access Point544. Enter “manager” for the username and “friend” for the password. The username and password are case-sensitiv

AT-TQ2450 Wireless Access Point Installation Guide55Setting the Country SettingYou should set the country setting during the initial management sessio

Chapter 2: Installing the Access Point56If you click OK, the access point changes the country setting and disables both radios on the access point.Thi

57Appendix ATechnical SpecificationsPhysical SpecificationsEnvironmental SpecificationsTable 4. AT-TQ2450 Physical SpecificationsDimensions (W x D x

Appendix A: Technical Specifications58Power SpecificationsTable 7. AT-TQ2450 Maximum Power ConsumptionAT-TQ2450 11.0 WTable 8. Power Adapter Input

AT-TQ2450 Wireless Access Point Installation Guide59LAN PortFigure 32 illustrates the pin layout of the LAN port.Figure 32. Pin Numbers for the RJ-45

6

Appendix A: Technical Specifications60Table 13 lists the pin signals when the LAN port is operating at 1000 Mbps.6TX-Table 13. 1000Base-T Connector

AT-TQ2450 Wireless Access Point Installation Guide61Safety and Electromagnetic Emissions CertificationsSafety and Electromagnetic Emissions Certificat

Appendix A: Technical Specifications62

63Appendix BRegulatory StatementsThis appendix contains the following regulatory statements: “Federal Communication Commission Interference Statement

Appendix B: Regulatory Statements64Federal Communication Commission Interference StatementThis device complies with Part 15 of the FCC Rules. Operatio

AT-TQ2450 Wireless Access Point Installation Guide65Industry Canada StatementThis device complies with RSS-210 of the Industry Canada Rules. Operation

Appendix B: Regulatory Statements66(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz

AT-TQ2450 Wireless Access Point Installation Guide67Europe - EU Declaration of ConformityThis device complies with the essential requirements of the R

Appendix B: Regulatory Statements68This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may

AT-TQ2450 Wireless Access Point Installation Guide69Italiano [Italian]Con la presente Allied Telesis dichiara che questo wireless access point è confo

7Preface ...

Appendix B: Regulatory Statements70Svenska [Swedish]Härmed intygar Allied Telesis att denna wireless access point står I överensstämmelse med de väsen

Contents8

9FiguresFigure 1: Front Panel..............................