Allied Telesis AT-8000GS Guia do Utilizador

613-001021 Rev. AManagementSoftwareAT-S95Web Browser InterfaceUser’s GuideAT-8000GS Series Stackable Gigabit Ethernet SwitchesVersion 1.0.1

Getting StartedStarting the ApplicationPage 10Figure 2: System General Page

Configuring InterfacesDefining MAC Based GroupsPage 100Defining MAC Based GroupsThe MAC Based Groups Page allows network managers to group VLANs based

Configuring InterfacesDefining MAC Based GroupsPage 101• Group ID — Defines the protocol group ID to which the interface is added.• VLAN ID — Attaches

Configuring InterfacesDefining MAC Based GroupsPage 102To add a mapped group:1. Click Layer 2 > MAC Based Groups. The MAC Based Groups Page opens:2

Configuring System LogsPage 103Section 8. Configuring System LogsThis section provides information for managing system logs. System logs enable viewin

Configuring System LogsPage 104The Event Log Page page contains fields for defining which events are recorded to which logs. It contains fields for en

Configuring System LogsPage 105• IP Address — Displays the defined IP address of the syslog server.• Minimum Severity — Indicates the defined minimum

Configuring System LogsPage 106• Facility — Defines an application from which system logs are sent to the remote server. Only one facility can be assi

Configuring System LogsPage 107Figure 80: View Flash Log PageThe View Flash Log Page and View Temporary Log Page list the following information:• Log

Configuring Spanning TreeConfiguring Classic Spanning TreePage 108Section 9. Configuring Spanning TreeSpanning Tree Protocol (STP) provides tree topog

Configuring Spanning TreeConfiguring Classic Spanning TreePage 109Defining STP PropertiesThe Spanning Tree Page contains parameters for enabling and c

Getting StartedUsing the Web Browser InterfacePage 11Using the Web Browser InterfaceThis section provides general information about the interface, and

Configuring Spanning TreeConfiguring Classic Spanning TreePage 110• Path Cost Default Values — Specifies the method used to assign default path cost t

Configuring Spanning TreeConfiguring Classic Spanning TreePage 111Defining STP InterfacesNetwork administrators can assign STP settings to a specific

Configuring Spanning TreeConfiguring Classic Spanning TreePage 112• Port Fast — Indicates if Fast Link is enabled on the port. If Fast Link mode is en

Configuring Spanning TreeConfiguring Classic Spanning TreePage 113Figure 83: Spanning Tree Configuration PageIn addition to the STP Interface Configur

Configuring Spanning TreeConfiguring Rapid Spanning TreePage 114Configuring Rapid Spanning TreeWhile Classic STP prevents Layer 2 forwarding loops in

Configuring Spanning TreeConfiguring Rapid Spanning TreePage 115• Mode — Displays the current STP mode. The STP mode is selected in the Spanning Tree

Configuring Spanning TreeConfiguring Multiple Spanning TreePage 116Configuring Multiple Spanning TreeMultiple Spanning Tree Protocol (MSTP) provides d

Configuring Spanning TreeConfiguring Multiple Spanning TreePage 117The MSTP Page contains the following fields: • Region Name — User-defined STP regio

Configuring Spanning TreeConfiguring Multiple Spanning TreePage 118The MSTP Interface Settings Page contains the following fields: • Instance ID — Lis

Configuring Spanning TreeConfiguring Multiple Spanning TreePage 1193. Define the fields.4. Click Apply. MSTP is defined for the selected interface.5.

Getting StartedUsing the Web Browser InterfacePage 12User Interface ComponentsThe System General Page example shows the interface components.Figure 4:

Configuring Spanning TreeConfiguring Multiple Spanning TreePage 120Defining MSTP Instance MappingsNetwork administrators can assign MSTP mapping to a

Configuring Spanning TreeConfiguring Multiple Spanning TreePage 121Defining MSTP Instance SettingsMSTP maps VLANs into STP instances. Packets assigned

Configuring Spanning TreeConfiguring Multiple Spanning TreePage 1223. Define the fields.4. Click Apply. MSTP is defined for the selected instance, and

Configuring Multicast ForwardingPage 123Section 10. Configuring Multicast ForwardingMulticast forwarding allows a single packet to be forwarded to mul

Configuring Multicast ForwardingPage 124Configuring IGMP SnoopingWhen IGMP Snooping is enabled globally, all IGMP packets are forwarded to the CPU. Th

Configuring Multicast ForwardingPage 125• IGMP Snooping Status — Indicates if IGMP snooping is enabled on the VLAN. The possible field values are: – E

Configuring Multicast ForwardingPage 126Figure 92: IGMP Configuration PageIn addition to the IGMP Page, the IGMP Configuration Page contains the follo

Configuring Multicast ForwardingPage 127Figure 93: Multicast Group PageThe Multicast Group Page contains the following fields:• Enable Bridge Multicas

Configuring Multicast ForwardingPage 128Figure 94: Add Multicast Group Page 4. Select the VLAN ID.5. Enter the Bridge Multicast MAC Address and the Br

Configuring Multicast ForwardingPage 129Defining Multicast Forward All SettingsMulticast forwarding enables transmitting packets from either a specifi

Getting StartedUsing the Web Browser InterfacePage 13Using the Management Buttons Management buttons provide an easy method of configuring device info

Configuring Multicast ForwardingPage 1302. Select interfaces to modify.3. Click Modify. The Multicast Forward All Configuration Page opens:Figure 97:

Configuring SNMPPage 131Section 11. Configuring SNMPSimple Network Management Protocol (SNMP) provides a method for managing network devices. Equipmen

Configuring SNMPPage 132the MIBs.All parameters are manageable from any SNMP management platform, except the SNMP management station IP address and co

Configuring SNMPPage 133Enabling SNMPThe SNMP Global Page provides fields for globally enabling and configuring SNMP on the device.To enable SNMP: 1.

Configuring SNMPPage 134Defining SNMP CommunitiesAccess rights are managed by defining communities in the SNMP Community Page. When the community name

Configuring SNMPPage 135SNMP Communities Basic TableThe SNMP Communities Basic Table contains the following fields:• Management Station — Displays the

Configuring SNMPPage 136• Access Mode — Defines the access rights of the community. The possible field values are:– Read Only — Management access is r

Configuring SNMPPage 137Figure 101:Community Configuration Page3. Define the Basic or Advanced configuration of the community.4. Click Apply. The SNMP

Configuring SNMPPage 138Defining SNMP GroupsThe SNMP Group Page provides information for creating SNMP groups, and assigning SNMP access control privi

Configuring SNMPPage 139– Write — Management access is read-write and changes can be made to the assigned SNMP view.– Notify — Sends traps for the ass

Getting StartedUsing the Web Browser InterfacePage 14Adding, Modifying and Deleting InformationThe WBI contains and tables for configuring devices. Us

Configuring SNMPPage 140Defining SNMP UsersThe SNMP Users Page enables assigning system users to SNMP groups, as well as defining the user authenticat

Configuring SNMPPage 141• Authentication — Displays the method used to authenticate users. The possible field values are:– MD5 Key — Users are authent

Configuring SNMPPage 142• Authentication Key — Defines the HMAC-MD5-96 or HMAC-SHA-96 authentication level. The authentication and privacy keys are en

Configuring SNMPPage 143Defining SNMP ViewsThe SNMP views provide or block access to device features or portions of features. Feature access is grante

Configuring SNMPPage 144Figure 109:Add SNMP VIew Page3. Define the View Name field.4. Select the Subtree ID Tree using one of the following options:–

Configuring SNMPPage 145Defining Notification RecipientsThe SNMP Notify Page contains fields for defining SNMP notification recipients. the page conta

Configuring SNMPPage 146SNMPv1,2c Notification RecipientThe SNMP v1, v2c Recipient table contains the following fields:• Recipients IP — Displays the

Configuring SNMPPage 147Figure 111: Add Notify Page 3. Define the relevant fields.4. Click Apply. The notification recipient settings are saved and th

Configuring SNMPPage 148Figure 112: SNMP Notify Configuration Page3. Define the fields.4. Click Apply. The SNMP Notification configuration is modified

Configuring SNMPPage 149Defining Notification FiltersThe SNMP Notification Filter Page permits filtering traps based on OIDs. Each OID is linked to a

Getting StartedLogging OutPage 154. Define the fields. 5. Click Apply. The fields are modified, and the information is saved to the device. To delete

Configuring SNMPPage 150To add an SNMP notification filter:1. Click the Add button. The Add SNMP Notification Filter Page opens:Figure 114: Add SNMP N

Configuring Power Over EthernetPage 151Section 12. Configuring Power Over EthernetThis section describes configuring Power over Ethernet (PoE) for an

Configuring Power Over EthernetPage 152Figure 115: Power Over Ethernet Page The Power Over Ethernet Page contains the following fields:Global PoE Conf

Configuring Power Over EthernetPage 153Defining Power Over Ethernet ConfigurationTo modify PoE port settings: 1. In the Power Over Ethernet Page Zoom

Configuring Power Over EthernetPage 154– Fault — Indicates one of the following:– The powered device test has failed. For example, a port could not be

Configuring ServicesPage 155Section 13. Configuring ServicesThis section describes Quality of Service related configurations. QoS supports activating

Configuring ServicesPage 156Enabling Class of Service (CoS)The CoS Page enables configuring the CoS ports or trunks on the device.To configure CoS por

Configuring ServicesPage 157• Select the interfaces displayed in the table.– Ports of Unit — Specifies the port and stacking member for which the CoS

Configuring ServicesPage 158Configuring CoS Queueing and SchedulingThe CoS Queuing & Scheduling Page provides fields for configuring CoS Priority

Configuring ServicesPage 159Mapping CoS Values to QueuesThe Configure CoS Page contains fields for classifying CoS settings to traffic queues.To set C

Getting StartedResetting the DevicePage 16Resetting the DeviceThe Reset option enables resetting the device from a remote location. NoteSave all chang

Configuring ServicesPage 160Mapping DSCP Values to QueuesThe Configure DSCP Page contains fields for classifying DSCP settings to traffic queues. For

Configuring ServicesPage 161The Configure DSCP Page contains the following fields:• Restore Defaults — Restores the device factory defaults for mappin

Configuring ServicesPage 162As a default the Bandwidth Page opens displaying the port options. The fields are identical when displaying the trunk CoS.

System UtilitiesPage 163Section 14. System UtilitiesThe configuration file structure involves the following configuration files:• Startup Configuratio

System UtilitiesPage 164Restoring the Default Configurationin the System Utilities Page, the Reset to Factory Defaults function restores the Configura

System UtilitiesPage 1652. Select the After Reset image file.3. Click Apply (below the table). The factory defaults are restored, and the device is up

System UtilitiesPage 166If the TFTP Operation is Configuration, the possible values are:– Running Configuration — Contains the configuration currently

System UtilitiesPage 167Viewing Integrated Cable TestsThe Cable Test Page contains fields for performing tests on copper cables. Cable testing provide

System UtilitiesPage 168• Cable Length — Indicates the approximate cable length. This test can only be performed when the port is up and operating at

System UtilitiesPage 169Viewing Optical TransceiversThe Optical Transceivers Page allows network managers to perform tests on Fiber Optic cables. Opti

Defining System InformationPage 17Section 2. Defining System InformationThe contains general device information, including system name and its IP add

System UtilitiesPage 170Resetting the DeviceThe Reset page enables the user to reset the system. Save all changes to the Running Configuration file be

Viewing StatisticsViewing Device StatisticsPage 171Section 15. Viewing StatisticsThe device provides statistics for RMON, interfaces, and Etherlike. T

Viewing StatisticsViewing Device StatisticsPage 172The Interface Statistics Page contains the following fields:• Select the interfaces displayed in th

Viewing StatisticsViewing Device StatisticsPage 173Viewing Etherlike Statistics The Etherlike Statistics Page displays interface statistics. To view E

Viewing StatisticsViewing Device StatisticsPage 174• Excessive Collisions — Displays the number of excessive collisions received on the selected inter

Viewing StatisticsManaging RMON StatisticsPage 175Managing RMON StatisticsThis section contains the following topics: • Viewing RMON Statistics• Confi

Viewing StatisticsManaging RMON StatisticsPage 176• Refresh Rate — Defines the frequency of the RMON statistics updates. The possible field values are

Viewing StatisticsManaging RMON StatisticsPage 177Configuring RMON HistoryThe RMON History Page contains information about samples of data taken from

Viewing StatisticsManaging RMON StatisticsPage 1782. Click Add. The Add RMON History Page opens:Figure 134:Add RMON History PageIn addition to the RMO

Viewing StatisticsManaging RMON StatisticsPage 179Viewing the RMON History TableThe RMON History Table Page contains interface specific statistical ne

Defining System InformationPage 18• Default Gateway — The IP address of a router for remote management of the device. The address must be entered in t

Viewing StatisticsManaging RMON StatisticsPage 180• CRC Align Errors — Displays the number of CRC and Align errors that have occurred on the interface

Viewing StatisticsManaging RMON StatisticsPage 181Configuring RMON EventsThe RMON Events Page contains fields for defining, modifying and viewing RMON

Viewing StatisticsManaging RMON StatisticsPage 182Figure 138:Add RMON Events Page3. Define the Community, Description, Type and Owner fields.4. Click

Viewing StatisticsManaging RMON StatisticsPage 183Viewing the RMON Events LogsThe RMON Events Logs Page contains interface specific statistical networ

Viewing StatisticsManaging RMON StatisticsPage 184Defining RMON Alarms The RMON Alarm Page contains fields for setting network alarms. Network alarms

Viewing StatisticsManaging RMON StatisticsPage 185• Rising Event — Displays the event that triggers the specific alarm. The possible field values are

Viewing StatisticsManaging RMON StatisticsPage 186Figure 143:Alarm Configuration Page3. Define the fields.4. Click Apply. The RMON alarm is saved, and

Managing StackingStacking OverviewPage 187Section 16. Managing StackingThis section describes the stacking control management and includes the followi

Managing StackingStacking OverviewPage 188Stacking Chain TopologyIn a chain topology, there are two units that have only one neighbor. Every unit has

Managing StackingStacking OverviewPage 189Each port in the stack has a specific Unit ID, port type, and port number, which are part of both the config

Configuring System TimePage 19Section 3. Configuring System TimeThe System Time Page provides information for configuring system time parameters, incl

Managing StackingConfiguring Stacking ManagementPage 190Configuring Stacking ManagementThe Stacking Page allows network managers to either reset the e

System DefaultsPage 191Appendix A. System DefaultsThis section contains the system defaults, and includes the following topics:• RS-232 Port Settings•

System DefaultsRS-232 Port SettingsPage 192RS-232 Port SettingsThe following table contains the RS-232 port setting defaults: Port DefaultsThe followi

System DefaultsConfiguration DefaultsPage 193Configuration DefaultsThe following are the initial device configuration defaults: Security DefaultsThe f

System DefaultsSpanning Tree DefaultsPage 194Spanning Tree DefaultsThe following are the spanning tree defaults:Address Table DefaultsThe following th

System DefaultsTrunking DefaultsPage 195Trunking DefaultsThe following are the trunking defaults:Multicast DefaultsThe following are the Multicast def

Downloading Software with CLIConnecting a TerminalPage 196Appendix B. Downloading Software with CLIThis section describes how to download system files

Downloading Software with CLIInitial ConfigurationPage 197Initial ConfigurationBefore a device can download system software, the device must have an i

Downloading Software with CLIDownloading SoftwarePage 198To check the configuration, enter the command “show ip interface” as illustrated in the follo

Downloading Software with CLIDownloading SoftwarePage 1992. Enter the copy command to download the boot file.3. Enter the “bootvar” command to determi

Copyright © 2008 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied

Configuring System TimePage 20The Clock Source and System Time sections of the System Time Page contain the following fields:• Clock Source — The sour

Downloading Software with CLIDownloading SoftwarePage 2005. Enter the “copy” command to download the system file.6. Reboot the device. The device boot

Downloading Software with CLIDownloading SoftwarePage 201Stacking Member Software DownloadEnsure the stack has been correctly connected as described i

Downloading Software with CLIDownloading SoftwarePage 2025. Enter the “copy” command to download the system file.6. Reboot the devices being updated.

IndexPage 203IndexSymbols802.1x port access 50AAbsolute 184Access level 44Access profiles 26access profilesrules 30ACE 55ACL 55, 66ACL Binding 66Alarm

IndexPage 204Guest VLAN 50GVRP 99configuration 98GVRP configuration 98, 99HHost 101HTTP 28, 37IIGMP 124IGMPv1 and 2 124IGMPv3 124Informational 104inte

IndexPage 205RSTP 114Rules 28SSamples 177Scheduling 158Secure HTTP 28, 37Secure Telnet 28Secure telnet 36security802.1x port access 50server based aut

Configuring System TimePage 21Broadcast Time InformationBroadcast information is used when the server IP address is unknown. When a broadcast message

Configuring System TimePage 22– Time — The time at which DST begins. The field format is HH:MM. For example: 05:30.• To — Indicates the time that DST

Configuring System TimePage 23• Canada — From the first Sunday in April until the last Sunday of October. Daylight Saving Time is usually regulated by

Configuring System TimePage 24• Turkey — From the last weekend of March until the last weekend of October.• United Kingdom — From the last weekend of

Configuring Device SecurityPage 25Section 4. Configuring Device SecurityThis section describes setting security parameters for ports, device managemen

Configuring Device SecurityConfiguring Management SecurityPage 26Configuring Management SecurityThis section provides information for configuring devi

Configuring Device SecurityConfiguring Management SecurityPage 27Figure 10: Access Profile PageThe Access Profile Page contains a table listing the cu

Configuring Device SecurityConfiguring Management SecurityPage 28Figure 11: Add Access Profile PageThe Add Access Profile Page contains the following

Configuring Device SecurityConfiguring Management SecurityPage 29• Action — Defines the action attached to the access rule. The possible field values

Page 3 ContentsPreface...

Configuring Device SecurityConfiguring Management SecurityPage 30Defining Profile RulesAccess profiles can contain up to 128 rules that determine whic

Configuring Device SecurityConfiguring Management SecurityPage 31• Management Method — Defines the management method for which the rule is defined. Us

Configuring Device SecurityConfiguring Management SecurityPage 32To modify an access rule:1. Click Mgmt. Security > Profile Rules: The Profile Rule

Configuring Device SecurityConfiguring Management SecurityPage 33Defining Authentication ProfilesAuthentication profiles allow network administrators

Configuring Device SecurityConfiguring Management SecurityPage 34– RADIUS — Authenticates the user at the RADIUS server. For more information, see Def

Configuring Device SecurityConfiguring Management SecurityPage 354. Enter the Profile Name.5. Using the arrows, move the method(s) from the Optional M

Configuring Device SecurityConfiguring Management SecurityPage 36Mapping Authentication ProfilesAfter authentication profiles are defined, they can be

Configuring Device SecurityConfiguring Management SecurityPage 37• Secure HTTP — Indicates that authentication methods are used for secure HTTP access

Configuring Device SecurityConfiguring Server Based AuthenticationPage 38Configuring Server Based AuthenticationNetwork administrators assign authenti

Configuring Device SecurityConfiguring Server Based AuthenticationPage 39The TACACS+ Page contains the following fields:• Timeout for Reply — Defines

Page 4 Configuring DHCP Snooping ... 68Defining DHCP Snoo

Configuring Device SecurityConfiguring Server Based AuthenticationPage 40To modify TACACS+ server settings:1. Click Mgmt. Protocols > TACACS+. The

Configuring Device SecurityConfiguring Server Based AuthenticationPage 41Configuring RADIUSRemote Authorization Dial-In User Service (RADIUS) servers

Configuring Device SecurityConfiguring Server Based AuthenticationPage 42• Authentication Port — Identifies the authentication port. The authenticatio

Configuring Device SecurityConfiguring Server Based AuthenticationPage 43Figure 24: RADIUS Configuration Page3. Define the relevant fields.4. Click Ap

Configuring Device SecurityConfiguring Server Based AuthenticationPage 44Configuring Local UsersNetwork administrators can define users, passwords, an

Configuring Device SecurityConfiguring Server Based AuthenticationPage 45Figure 26: Add Local User PageIn addition to the fields in the Local Users Pa

Configuring Device SecurityConfiguring Server Based AuthenticationPage 46Defining Line PasswordsNetwork administrators can define line passwords in th

Configuring Device SecurityConfiguring Network SecurityPage 47Configuring Network SecurityNetwork security manages locked ports.Port-based authenticat

Configuring Device SecurityConfiguring Network SecurityPage 48Figure 29: Port Security PageThe Port Security Page displays the Zoom View of the select

Configuring Device SecurityConfiguring Network SecurityPage 49Figure 30: Port Security Configuration PageThe Port Security Configuration Page contains

Page 5 Defining SNMP Views...

Configuring Device SecurityConfiguring Network SecurityPage 50Defining 802.1x Port AccessThe 802.1x Port Access Page allows enabling port access globa

Configuring Device SecurityConfiguring Network SecurityPage 51The 802.1x Port Access Page also displays the Zoom View of the selected stacking member’

Configuring Device SecurityConfiguring Network SecurityPage 52• Admin Port Control — Indicates the port state. The possible field values are:– Auto —E

Configuring Device SecurityConfiguring Network SecurityPage 53Enabling Storm ControlStorm control limits the amount of unknown Unicast, Multicast and

Configuring Device SecurityConfiguring Network SecurityPage 54Figure 34: Storm Control Configuration PageThe Storm Control Configuration Page contains

Configuring Device SecurityDefining Access ControlPage 55Defining Access ControlAccess Control Lists (ACL) allow network managers to define classifica

Configuring Device SecurityDefining Access ControlPage 56The MAC Based ACL Page contains the following fields:• ACL Name — Displays the specific MAC b

Configuring Device SecurityDefining Access ControlPage 57Figure 36: Add MAC Based ACL Page3. In the ACL Name field, type a name for the ACL.4. Enable

Configuring Device SecurityDefining Access ControlPage 58Figure 37: Add MAC Based ACE Page3. Define the fields.4. Click Apply. The MAC Based ACE rule

Configuring Device SecurityDefining Access ControlPage 593. Define the fields.4. Click Apply. The MAC Based ACL configuration is defined, and the devi

Page 6 Spanning Tree Defaults ...194Address T

Configuring Device SecurityDefining Access ControlPage 60Defining IP Based ACLThe IP Based ACL Page contains information for defining IP Based ACLs, i

Configuring Device SecurityDefining Access ControlPage 61– TCP — Transmission Control Protocol (TCP). Enables two hosts to communicate and exchange da

Configuring Device SecurityDefining Access ControlPage 62• Destination– IP Address — Matches the destination port IP address to which packets are addr

Configuring Device SecurityDefining Access ControlPage 63Figure 40: Add IP Based ACL PageIn addition to the IP Based ACL Page, the Add IP Based ACL Pa

Configuring Device SecurityDefining Access ControlPage 64Adding ACE Rules1. Click Network Security > IP Based ACL. The IP Based ACL Page opens.2. C

Configuring Device SecurityDefining Access ControlPage 65Figure 42: IP Based ACL Configuration Page3. Define the fields.4. Click Apply. The IP Based A

Configuring Device SecurityDefining Access ControlPage 66Defining ACL BindingWhen an ACL is bound to an interface, all the ACE rules that have been de

Configuring Device SecurityDefining Access ControlPage 67Figure 44: ACL Binding ConfigurationThe ACL Binding Configuration contains the following fiel

Configuring DHCP SnoopingPage 68Section 5. Configuring DHCP SnoopingDHCP Snooping expands network security by providing an extra layer of security bet

Configuring DHCP SnoopingPage 69Figure 45: DHCP Snooping General PageThe DHCP Snooping General Page contains the following fields:• Enable DHCP Snoopi

PrefaceWeb Browser Interface User’s Guide OverviewPage 7PrefaceThis guide contains instructions on how to configure an AT-S95 Series Layer 2+ Gigabit

Configuring DHCP SnoopingPage 70• DHCP Option 82 Insertion — DHCP Option 82 attaches authentication messages to the packets sent to DHCP Server via TC

Configuring DHCP SnoopingPage 71Defining Trusted InterfacesThe Trusted Interfaces Page allows network manager to define Trusted interfaces. Trusted in

Configuring DHCP SnoopingPage 722. From the global Interface field, define the specific port or trunk.3. In the table, select an interface and click M

Configuring DHCP SnoopingPage 73Binding Addresses to the DHCP Snooping DatabaseThe Binding Database Page contains parameters for querying and adding I

Configuring DHCP SnoopingPage 74Query ResultsThe Query Results table contains the following fields:• MAC Address — Indicates the MAC address found dur

Configuring PortsSetting Ports ConfigurationsPage 75Section 6. Configuring PortsPort Configuration includes the following procedures for configuring p

Configuring PortsSetting Ports ConfigurationsPage 763. Click Modify. The Port Setting Configuration Page opens:Figure 52: Port Setting Configuration P

Configuring PortsSetting Ports ConfigurationsPage 77• Admin Status — Displays the link operational status. The possible field values are: – Up — Indic

Configuring PortsSetting Ports ConfigurationsPage 78• Admin Advertisement — Defines the auto negotiation setting the port advertises. The possible fie

Configuring PortsSetting Ports ConfigurationsPage 79Configuring Port MirroringPort mirroring monitors and mirrors network traffic by forwarding copies

PrefaceIntended AudiencePage 8• Section 16, “Managing Stacking” — Provides information for stacking, including a stacking overview. • Appendix A, “Dow

Configuring PortsSetting Ports ConfigurationsPage 80• Status — Indicates if the port is currently monitored. The possible field values are:– Active —

Configuring PortsSetting Ports ConfigurationsPage 813. Define the Type field.4. Click Apply. The Port mirroring is modified, and the device is updated

Configuring PortsAggregating PortsPage 82Aggregating Ports Link Aggregation optimizes port usage by linking a group of ports together to form a single

Configuring PortsAggregating PortsPage 83Figure 56: Trunk Settings PageThe Trunk Settings Page displays information about the currently defined trunks

Configuring PortsAggregating PortsPage 84– Disable — LACP is disabled on the trunk.• PVE — Enables a port to be a Private VLAN Edge (PVE) port. When a

Configuring PortsAggregating PortsPage 85• Current Status — Indicates whether the trunk is currently operational or non-operational. The possible fiel

Configuring PortsAggregating PortsPage 86• PVE — Enables a port to be a Private VLAN Edge (PVE) port. When a port is defined as PVE, it bypasses the F

Configuring PortsAggregating PortsPage 87Figure 59: Port Trunking Configuration PageIn addition to the fields in the The Port Trunking Page, the Port

Configuring PortsAggregating PortsPage 88Configuring LACPTrunk ports can contain different media types if the ports are operating at the same speed. A

Configuring PortsAggregating PortsPage 89Figure 61: LACP Configuration Page3. Define the fields.4. Click Apply. The LACP settings are saved and the de

Getting StartedStarting the ApplicationPage 9Section 1. Getting StartedThis section provides an introduction to the Web Browser Interface, and include

Configuring InterfacesPage 90Section 7. Configuring InterfacesThis section contains information on configuring the interfaces of the device.This secti

Configuring InterfacesPage 91The MAC Address Page contains the following fields:• View Static — Displays the static addresses assigned to the ports on

Configuring InterfacesPage 92To delete all MAC addresses: 1. Click Layer 2 > MAC Address. The MAC Address Page opens.2. Click Delete in the Delete

Configuring InterfacesConfiguring VLANsPage 93Configuring VLANs This section describes how to create and configure Virtual LANs (VLANs).VLANs are logi

Configuring InterfacesConfiguring VLANsPage 94Defining VLAN PropertiesThe VLAN Page provides information and global parameters for configuring and wor

Configuring InterfacesConfiguring VLANsPage 95• Interface Status — Indicates the interface’s membership status in the VLAN. The possible field values

Configuring InterfacesConfiguring VLANsPage 96Defining VLAN Interface SettingsThe VLAN Interface Page contains fields for managing ports that are part

Configuring InterfacesConfiguring VLANsPage 97• PVID — Port Default VLAN ID. Assigns a VLAN ID to untagged packets. The possible values are 1-4094. VL

Configuring InterfacesConfiguring VLANsPage 98Defining GVRPThe GVRP Page enables users to configure GARP VLAN Registration Protocol (GVRP) on the devi

Configuring InterfacesConfiguring VLANsPage 99• Select the interfaces displayed in the table.– Ports of Unit — Specifies the port and stacking member