Allied Telesis AT-8100S/24C Guia de Instalação

613-001382 Rev. E8100L and 8100S SeriesFast Ethernet Switches AT-8100L/8 AT-8100L/8POE AT-8100L/8POE-E AT-8100S/24C AT-8100S/24 AT-8100S/24POE

Figures10

Chapter 5: Powering On the Switch100Telnet management sessions are not secure and are vulnerable to snooping because the packets exchanged between the

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches101 You need to assign your management workstation an IP address in the 169.

Chapter 5: Powering On the Switch102For instructions on the command line interface and the PORT parameter, refer to the AT-8100 Series AlliedWare Plus

103Chapter 6TroubleshootingThis chapter contains suggestions on how to troubleshoot the switch if a problem occurs.NoteFor further assistance, please

Chapter 6: Troubleshooting104 Verify that the network device connected to the twisted pair port is powered on and is operating properly. Try connect

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches105Problem 5: Network performance between a twisted pair port on the switch a

Chapter 6: Troubleshooting106

107Appendix ATechnical SpecificationsPhysical SpecificationsDimensions (H x W x D)WeightsTable 17. Product DimensionsAT-8100L/8AT-8100L/8POEAT-8100L/8

Appendix A: Technical Specifications108VentilationEnvironmental SpecificationsAT-8100S/16F8-LC 4.4 kg (9.75 lb.)AT-8100S/24F-LC 4.4 kg (9.75 lb.)Table

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches109Power SpecificationsMaximum Power ConsumptionsInput VoltagesTable 22. Maxi

11TablesTable 1: Hardware Features of the 8100L Series Switches ...

Appendix A: Technical Specifications110CertificationsQuality and ReliabilityAT-8100S/48 AC model: 100-240 VAC, 1.0 A maximum, 50/60 Hz per inputAT-810

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches111RJ-45 Twisted Pair Port PinoutsFigure 45 illustrates the pin layout of the

Appendix A: Technical Specifications112Table 27 lists the pin signals when a port operating at 1000 Mbps.Fiber Optic Port SpecificationsTable 28 lists

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches113Table 29 lists the specifications of the 100Base-FX fiber optic ports on t

Appendix A: Technical Specifications114RJ-45 Style Serial Console Port PinoutsTable 30 lists the pin signals of the RJ-45 style serial Console port.St

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches1154 Transmit data1+ Receive data1+5 Ground Ground6 Transmit data1- Receive d

Appendix A: Technical Specifications116

Tables12

13PrefaceThis guide contains the installation instructions for the 8100L and 8100S Series of Fast Ethernet switches. This manual explains how to insta

Preface14Document ConventionsThis document uses the following conventions:NoteNotes provide additional information.CautionCautions inform you that per

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches15Contacting Allied TelesisIf you need assistance with this product, you may

Preface16

17Chapter 1 OverviewThis chapter contains the following sections: “Features” on page 18 “8100L Series Switches” on page 22 “8100S Twisted Pair Seri

Chapter 1: Overview18FeaturesHere is a list of the switches and their features:8100L and 8100SModelsHere are the 8100L and 8100S Series switches: AT-

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches19Power overEthernetHere are the basic features of Power over Ethernet (PoE):

Copyright  2012 Allied Telesis, Inc.All rights reserved. No part of this publication may be reproduced without prior written permission from Allied T

Chapter 1: Overview20Stacking Ports Here are the basic features of the stacking ports on the 8100S Series switches: Two stacking ports per switch 10

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches21Fanless Models Here are the 8100L and 8100S Series switches that do not hav

Chapter 1: Overview228100L Series SwitchesThe three models in the 8100L Series are listed here: AT-8100L/8 AT-8100L/8POE AT-8100L/8POE-EHardwareFea

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches23Front Panels The front panels of the 8100L Series switches are shown in Fig

Chapter 1: Overview248100S Twisted Pair Series SwitchesThe five twisted pair models in the 8100S Series are listed here: AT-8100S/24C AT-8100S/24 A

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches25Front Panels The front panels of the 8100S Series switches are shown in Fig

Chapter 1: Overview26Front PanelComponentsFigure 4 identifies the Fast and Gigabit Ethernet networking ports and the SFP slots on the 8100S Series swi

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches278100S Fiber Optic Series SwitchesThe three fiber optic models in the 8100S

Chapter 1: Overview28Front Panels The front panels of the fiber optic switches are shown in Figure 5 and Figure 6 on page 29.Figure 5. Front Panels of

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches29Figure 6. Front Panels of the 8100S Fiber Optic Series Switches (Continued)

3Electrical Safety and Emissions StandardsThis product meets the following standards.RFI Emissions: FCC Class A, EN55022 Class A, EN61000-3-2, EN61000

Chapter 1: Overview30Back PanelsFigure 7 shows the back panels of the single power supply switches.Figure 7. Back Panels of the Single Power Supply Sw

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches31Figure 8 shows the back panels of the dual power supply switches.Figure 8.

Chapter 1: Overview32Management PanelsFigure 9 identifies the components in the management panel on the 8100L Series switches.Figure 9. 8100L Series M

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches33Model Naming ConventionsThe hardware features of the switches are represent

Chapter 1: Overview34The conventions are defined in Table 6.Table 6. Model Naming Conventions for the Fiber Optic 8100S Series SwitchesConvention Defi

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches3510/100Base-TX Twisted Pair PortsThe switches have 8, 24, or 48 10/100Base-T

Chapter 1: Overview36MaximumDistanceThe ports have a maximum operating distance of 100 meters (328 feet).Power OverEthernetThe 10/100Base-TX ports on

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches3710/100/1000Base-T Twisted Pair PortsThe switches have two 10/100/1000Base-T

Chapter 1: Overview38The MDI and MDI-X settings do not apply when the ports are operating at 1000 Mbps.MaximumDistanceThe ports have a maximum operati

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches39SFP SlotsThe switches have two slots for 100Mbps 100Base-FX or 1000Mbps 100

4Translated Safety StatementsImportant: The  indicates that translations of the safety statement are available in the PDF document “Translated Safety

Chapter 1: Overview40 Port speed is an exception to the shared settings of the twisted pair port and SFP slot of a combo port. If you disable Auto-Ne

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches41Power Over EthernetThe AT-8100L/8POE, AT-8100L/8POE-E, AT-8100S/24POE, and

Chapter 1: Overview42Powered DeviceClassesPowered devices are grouped into the five classes listed in Table 10 on page 42. The classes are based on th

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches43The switch can handle different power requirements on different ports. This

Chapter 1: Overview44WiringImplementationThe IEEE 802.3af standard defines two methods by which a PSE, such as the switch, can transmit DC power over

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches45Stacking PortsThe 8100S Series switches may be used as stand-alone units or

Chapter 1: Overview46eco-friendly ButtonYou may turn off the port LEDs to conserve electricity when you are not monitoring the switch. The LEDs may be

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches47LEDsHere are descriptions of the switch’s LEDs.10/100Base-TXTwisted Pair Po

Chapter 1: Overview48Here are the LED guidelines: The LEDs do not display port speed. That information may be displayed using the management software

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches49100Base-FX PortLEDsEach of the 100Base-FX ports on the AT-8100S/16F8-SC, AT

5Preface ...

Chapter 1: Overview50SFP Slot LED Each SFP slot has one LED.Figure 16. SFP Slot LEDsThe SFP slot LED is described in Table 14.Table 14. SFP Slot LEDLE

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches51Stacking PortLEDsEach stacking port has one link LED labelled LINK/ACT.Figu

Chapter 1: Overview52Figure 18. Stack ID LEDThe 8100L Series switches do not support stacking, but they have stack ID LEDs and can be assigned ID numb

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches53Console PortThe Console port is used to configure the features and paramete

Chapter 1: Overview54Power SuppliesThe 8100L Series switches have one AC power supply. The 8100S Series switches have two AC or DC power supplies, exc

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches55Power ConnectorsThe 8100S Series switches have two AC or DC power supply so

Chapter 1: Overview56

57Chapter 2Beginning the InstallationThe chapter contains the following sections: “Installation Procedures” on page 58 “Reviewing Safety Precautions

Chapter 2: Beginning the Installation58Installation ProceduresYou may install the switch on a table or in an equipment rack. Perform these procedures

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches59Reviewing Safety PrecautionsPlease review the following safety precautions

Contents6Port Pinouts ...

Chapter 2: Beginning the Installation60WarningClass I Equipment. This equipment must be earthed. The power plug must be connected to a properly wired

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches61CautionRisk of explosion if battery is replaced by an incorrect type. Repla

Chapter 2: Beginning the Installation62WarningReliable earthing of rack-mounted equipment should be maintained. Particular attention should be given t

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches63Choosing a Site for the SwitchObserve these requirements when planning the

Chapter 2: Beginning the Installation64Unpacking the SwitchRefer to the following tables to verify the contents of the shipping containers of the swit

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches65Figure 19. Components of the 8100L Series SwitchesOne AT-8100L/8, AT-8100L/

Chapter 2: Beginning the Installation668100S SeriesSwitchesThe 8100S Series switches, except the AT-8100S/24C Switch, come with the components listed

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches67AT-8100S/24CSwitchThe AT-8100S/24C Switch comes with the items listed in Fi

Chapter 2: Beginning the Installation68

69Chapter 3Installing the Switch on a Table or in an Equipment RackThe procedures in this chapter are: “Installing the Switch on a Table or Desktop”

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches7Certifications...

Chapter 3: Installing the Switch on a Table or in an Equipment Rack70Installing the Switch on a Table or DesktopYou may install the switch on a table

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches71Installing the Switch in an Equipment RackThis procedure requires the follo

Chapter 3: Installing the Switch on a Table or in an Equipment Rack723. Turn the switch over.4. For all switches except the AT-8100L/8, AT-8100L/8POE,

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches73Figure 25. Attaching the Brackets to Install the Switch in an Equipment Rac

Chapter 3: Installing the Switch on a Table or in an Equipment Rack74Figure 26. Attaching the Brackets to 8100L and AT-8100S/24C Switches for Equipmen

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches75Figure 27. Attaching the Brackets to 8100L and AT-8100S/24C Switches for Eq

Chapter 3: Installing the Switch on a Table or in an Equipment Rack76

77Chapter 4Cabling the Networking PortsThis chapter contains the following procedures: “Cabling the Twisted Pair and Fiber Optic Ports” on page 78 “

Chapter 4: Cabling the Networking Ports78Cabling the Twisted Pair and Fiber Optic PortsThis section contains the guidelines to cabling the twisted pai

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches79 The 10/100/1000Base-T ports must be set to Auto-Negotiation, the default

Contents8

Chapter 4: Cabling the Networking Ports80Installing Optional SFP TransceiversReview the following guidelines before installing optional SFP transceive

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches81Figure 29. Removing the Dust Plug from an SFP Slot2. Remove the transceiver

Chapter 4: Cabling the Networking Ports82Figure 31. Removing the Dust Cover from the SFP Module6. Verify that the handle on the SFP transceiver is in

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches837. Connect the fiber optic cable to the SFP module, as shown in Figure 33.F

Chapter 4: Cabling the Networking Ports84

85Chapter 5Powering On the SwitchThis chapter contains the following procedures: “Powering On an AC Switch” on page 86 “Powering On a DC Switch” on

Chapter 5: Powering On the Switch86Powering On an AC SwitchTo power on an AC switch, connect the power cords to the connectors on the back panels and

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches87Consider the following items as you power on the switch: Connecting the tw

Chapter 5: Powering On the Switch88The base port LEDs are on in phases 1 and 2 if they are connected to live network devices. Otherwise, they are off.

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches89Figure 35. Switch Initialization MessagesCFE-NTSW-5.0.0 for BCM956218 (32bi

9Figure 1: Front Panels of the 8100L Series Switches...

Chapter 5: Powering On the Switch90Figure 36. Switch Initialization Messages (Continued)After the switch has initialized its management software, go t

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches91Powering On a DC SwitchPerform this procedure to power on a DC 8100S Series

Chapter 5: Powering On the Switch92Figure 37. DC Terminal Block3. With a 14-gauge wire-stripping tool, strip the three wires in the tray cable coming

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches93Figure 39. Inserting Wires into the DC Terminal Block5. Connect the positiv

Chapter 5: Powering On the Switch94computer with a terminal emulator program connected to the Console port on the switch, you will see the messages in

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches95Setting the Stack ID NumberAfter the switch has initialized its management

Chapter 5: Powering On the Switch962. Connect the other end of the cable to an RS-232 port on a terminal or PC with a terminal emulator program.3. Con

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches973. Connect the other end of the cable to the Ethernet port on your computer

Chapter 5: Powering On the Switch98This confirmation prompt in Figure 43 is displayed.Figure 43. STACK Command Confirmation PromptCautionThe STACK com

Stand-alone Switch Installation Guide for 8100L and 8100S Series Switches99Starting a Management SessionYou may use the following methods and tools to