Allied Telesis SB251-13 Manual do Utilizador

Simply connecting the world Patch Release NotePatch SB251-13For SwitchBlade 4000 Series Switches and AT-9800 Series SwitchesIntroductionThis patch rel

10 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MWhen typing “?” at the command line after SET SWITCH PORT, INGRESSLIM

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 11Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe CREA

12 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MPrefixes of Anycast addresses could not be shared on the same port. T

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 13Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe SET

14 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MBIST failures were occurring because the software was not full suppor

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 15Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MMulticas

16 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MMLD snooping on the switch uses the last 4 bytes of the IPv6 address

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 17Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MFigure 1

18 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MFigure 2: Example output from the SHOW MLDSNOOPING COUNTER command.Ta

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 19Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MFeatures

2 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MSome of the issues addressed in this Release Note include a level numb

20 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV M• IPv4 addresses x.x.x.0 or x.x.x.255 were not accepted for the LOCAL

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 21Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV Mconnecti

22 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe action of the MAJOR and MINOR relays does not presently match the

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 23Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MIf an IP

24 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV Mthe CREATE QOS TRAFFICCLASS MAXBANDWIDTH parameter. This issue has be

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 25Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe SNMP

26 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MWhen a radius lookup performed by the L2TP Access Concentrator (LAC)

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 27Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MEnabling

28 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MEntering a “?” on the command line, now displays the correct list of

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 29Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MENABLE I

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 3Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV M Ports on

30 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MDVMRP unicast Prune, Graft, and Graft-Ack messages are now switched a

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 31Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe PAGE

32 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MAn unnecessary check has been removed from the CREATE ISAKMP POLICY A

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 33Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MRIPng wa

34 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MIf a DVMRP interface was deleted and then added again, DVMRP routes a

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 35Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MWhen RIP

36 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MIf, with one or more routes already configured, BGP was enabled and a

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 37Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MOn Switc

38 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MBroadcast TCP packets were being processed by the device, causing fat

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 39Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV M Each ne

4 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV M The SET VLAN BCLIMIT command did not work when executed from start-up

40 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe MRU parameter in the SET PPP command was incorrectly handled as a

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 41Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MMultilin

42 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe DHCP lease Expiry time showed incorrectly in the SHOW DHCP CLIENT

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 43Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MWhen sta

44 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MPPP configured on a L2TP access concentrator (LAC) should be dynamic.

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 45Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MPIM Graf

46 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MTyping “?” for Help at the CLI for the SHOW SWITCH FDB command displa

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 47Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe spec

48 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MA forwarded PIM-DM state Refresh message did not update the metric an

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 49Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe comm

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 5Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MAn unknow

50 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe dot1dStpPortForwardTransitions value in the dot1dBridge MIB was n

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 51Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe GBLP

52 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe SHOW DHCP CLIENT command output showed a ClientId value even when

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 53Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MIPv6 sta

54 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MInvalid characters could be used in the SHOW CF DIR command. This iss

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 55Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MJumbo pa

56 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV Maddresses in that range that were not allocated at that time, resulti

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 57Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MFeatures

58 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MAn issue exists where the CAM entry 0 in the VLAN Tag table is either

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 59Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV M• The ou

6 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MBrowsing the dot1dTpFdbPort table with SNMPv2c sometimes gave incorrec

60 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MPatch SB251-05 includes all issues resolved and enhancements released

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 61Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV Mwas corr

62 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MSET SWITCH BLADE settings are now only added to the configuration fil

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 63Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MPackets

64 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MThe DPORT parameter in the ADD SWITCH HWFILTER command was omitted wh

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 65Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MFeatures

66 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MPause flow control is now disabled by default on all ports. This impr

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 7Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MA fatal e

8 Patch Release NotePatch SB251-13 for Software Release 2.5.1C613-10361-00 REV MHardware filters using classifiers that specified IP addresses were no

Patch SB251-13 For SwitchBlade 4000 Series Switches and AT-9800 Series Switches 9Patch SB251-13 for Software Release 2.5.1C613-10361-00 REV MFiles wer