Allied-telesis AT-S62 Manual do Utilizador Página 184
- Página / 420
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Chapter 10: Port Trunking Commands
184
SET SWITCH TRUNK
Syntax
set switch trunk=name
select=[macsrc|macdest|macboth|ipsrc|ipdest|
ipboth]
Parameters
trunk Specifies the name of the port trunk.
select Specifies the load distribution method. Options are:
macsrc Source MAC address.
macdest Destination MAC address.
macboth Source address/destination MAC
address.
ipsrc Source IP address.
ipdest Destination IP address.
ipboth Source address/destination IP
address.
Description
This command changes the load distribution method of an existing port
trunk. To view the trunks on a switch, refer to SHOW SWITCH TRUNK on
page 185.
Example
The following command changes the load distribution method of a
trunk named “Load11” to destination IP address:
set switch trunk=Load11 select=ipdest
- Command Line 1
- User’s Guide 1
- Table of Contents 3
- Document Conventions 12
- Contacting Allied Telesyn 13
- Starting a Command Line 15
- Management Session 15
- Starting a Management Session 16
- Command Formatting 18
- Basic Command Line Commands 19
- CLEAR SCREEN 20
- LOGOFF, LOGOUT and QUIT 23
- SAVE CONFIGURATION 25
- SET PROMPT 26
- SET SWITCH CONSOLEMODE 27
- SHOW USER 28
- Enhanced Stacking Commands 29
- ACCESS SWITCH 30
- SET SWITCH STACKMODE 32
- SHOW REMOTELIST 34
- Basic Switch Commands 35
- DISABLE DHCPBOOTP 37
- DISABLE IP REMOTEASSIGN 38
- DISABLE TELNET 39
- ENABLE IP REMOTEASSIGN 41
- ENABLE TELNET 42
- PURGE IP 44
- RESET SWITCH 45
- RESET SYSTEM 46
- RESTART REBOOT 47
- RESTART SWITCH 48
- SET ASYN 50
- SET IP INTERFACE 51
- SET IP ROUTE 53
- SET PASSWORD MANAGER 54
- SET PASSWORD OPERATOR 55
- SET SWITCH CONSOLETIMER 56
- SET SYSTEM 57
- SHOW CONFIG 58
- SHOW DHCPBOOTP 59
- SHOW IP ROUTE 61
- SHOW SWITCH 62
- SHOW SYSTEM 63
- Simple Network Time Protocol 64
- (SNTP) Commands 64
- ADD SNTPSERVER PEER 65
- DISABLE SNTP 67
- ENABLE SNTP 68
- PURGE SNTP 69
- SET DATE TIME 70
- SET SNTP 71
- SHOW SNTP 72
- SHOW TIME 73
- SNMPv1 and SNMPv2 Community 74
- Strings and Trap Commands 74
- ADD SNMP COMMUNITY 75
- CREATE SNMP COMMUNITY 77
- DESTROY SNMP COMMUNITY 81
- DISABLE SNMP 82
- DISABLE SNMP AUTHENTICATETRAP 83
- DISABLE SNMP COMMUNITY 84
- ENABLE SNMP 85
- ENABLE SNMP AUTHENTICATETRAP 86
- ENABLE SNMP COMMUNITY 87
- SET SNMP COMMUNITY 88
- SHOW SNMP 90
- SNMPv3 Commands 92
- ADD SNMPV3 USER 94
- CLEAR SNMPV3 ACCESS 96
- CLEAR SNMPV3 COMMUNITY 98
- CLEAR SNMPV3 NOTIFY 99
- CLEAR SNMPV3 TARGETADDR 100
- CLEAR SNMPV3 VIEW 101
- CREATE SNMPV3 ACCESS 102
- Chapter 7: SNMPv3 Commands 104
- DESTROY SNMPv3 ACCESS 118
- DESTROY SNMPv3 COMMUNITY 120
- DESTROY SNMPv3 GROUP 121
- DESTROY SNMPv3 NOTIFY 122
- DESTROY SNMPv3 TARGETADDR 123
- DESTROY SNMPv3 TARGETPARMS 124
- DESTROY SNMPV3 VIEW 125
- SET SNMPV3 ACCESS 126
- SET SNMPV3 COMMUNITY 128
- SET SNMPV3 GROUP 130
- SET SNMPV3 NOTIFY 132
- SET SNMPV3 TARGETADDR 134
- SET SNMPV3 TARGETPARAMS 136
- SET SNMPV3 USER 138
- SET SNMPV3 VIEW 140
- SHOW SNMPV3 ACCESS 142
- SHOW SNMPV3 COMMUNITY 143
- SHOW SNMPv3 GROUP 144
- SHOW SNMPV3 NOTIFY 145
- SHOW SNMPV3 TARGETADDR 146
- SHOW SNMPV3 TARGETPARAMS 147
- SHOW SNMPV3 USER 148
- SHOW SNMPV3 VIEW 149
- Port Parameter Commands 150
- ACTIVATE SWITCH PORT 151
- DISABLE INTERFACE LINKTRAP 152
- DISABLE SWITCH PORT 153
- DISABLE SWITCH PORT FLOW 154
- ENABLE INTERFACE LINKTRAP 155
- ENABLE SWITCH PORT 156
- ENABLE SWITCH PORT FLOW 157
- RESET SWITCH PORT 158
- SET SWITCH PORT 159
- SET SWITCH PORT RATELIMIT 164
- SHOW INTERFACE 167
- SHOW SWITCH PORT 169
- MAC Address Table Commands 170
- ADD SWITCH FDB 171
- DELETE SWITCH FDB 173
- RESET SWITCH FDB 174
- SHOW SWITCH FDB 176
- Port Trunking Commands 178
- ADD SWITCH TRUNK 179
- CREATE SWITCH TRUNK 180
- DELETE SWITCH TRUNK 182
- DESTROY SWITCH TRUNK 183
- SET SWITCH TRUNK 184
- SHOW SWITCH TRUNK 185
- Port Mirroring Commands 186
- SET SWITCH MIRROR 187
- SET SWITCH PORT MIRROR 188
- SHOW SWITCH MIRROR 189
- Statistics Commands 190
- RESET SWITCH PORT COUNTER 191
- SHOW SWITCH COUNTER 192
- SHOW SWITCH PORT COUNTER 193
- File System Commands 194
- CREATE CONFIG 196
- DELETE FILE 197
- SET CONFIG 199
- SHOW FILE 201
- File Download and Upload 202
- Commands 202
- Event Log Commands 212
- DISABLE LOG 213
- ENABLE LOG 214
- PURGE LOG 215
- SAVE LOG 216
- SET LOG FULLACTION 218
- SHOW LOG 219
- SHOW LOG STATUS 224
- Quality of Service (QoS) 225
- MAP QOS COSP 226
- SET QOS SCHEDULING 227
- SHOW QOS CONFIG 228
- IGMP Snooping Commands 229
- DISABLE IGMPSNOOPING 230
- ENABLE IGMPSNOOPING 231
- SET IP IGMP 232
- SHOW IGMPSNOOPING 234
- SHOW IP IGMP 235
- SET DOS IPOPTION 239
- SET DOS LAND 240
- SET DOS PINGOFDEATH 241
- SET DOS SMURF 243
- SET DOS SYNFLOOD 244
- SET DOS TEARDROP 245
- SHOW DOS 247
- STP Commands 249
- ACTIVATE STP 250
- DISABLE STP 251
- ENABLE STP 252
- PURGE STP 253
- Chapter 19: STP Commands 254
- RSTP Commands 260
- ACTIVATE RSTP 261
- DISABLE RSTP 262
- ENABLE RSTP 263
- PURGE RSTP 264
- SET RSTP 265
- Chapter 20: RSTP Commands 266
- SHOW RSTP 272
- MSTP Commands 274
- ACTIVATE MSTP 275
- ADD MSTP 276
- CREATE MSTP 277
- DELETE MSTP 278
- DESTROY MSTP MSTIID 279
- DISABLE MSTP 280
- ENABLE MSTP 281
- PURGE MSTP 282
- SET MSTP 283
- Chapter 21: MSTP Commands 284
- SET MSTP CIST 286
- SET MSTP MSTI 287
- SET MSTP PORT 290
- ADD VLAN 296
- CREATE VLAN 298
- DELETE VLAN 302
- DESTROY VLAN 305
- SET SWITCH INFILTERING 306
- SET SWITCH MANAGEMENTVLAN 307
- SET SWITCH VLANMODE 308
- SET VLAN 310
- SHOW VLAN 311
- DISABLE GARP 313
- ENABLE GARP 314
- PURGE GARP 315
- SET GARP PORT 316
- SET GARP TIMER 317
- SHOW GARP 319
- SHOW GARP COUNTER 320
- SHOW GARP DATABASE 322
- SHOW GARP GIP 323
- SHOW GARP MACHINE 324
- MAC Address Security 325
- SET SWITCH PORT SECURITYMODE 327
- SHOW SWITCH PORT INTRUSION 330
- SHOW SWITCH PORT SECURITYMODE 331
- DISABLE PORTACCESS 333
- DISABLE RADIUSACCOUNTING 334
- ENABLE PORTACCESS 335
- ENABLE RADIUSACCOUNTING 336
- SET RADIUSACCOUNTING 343
- SHOW PORTACCESS 345
- SHOW PORTACCESS 346
- SHOW RADIUSACCOUNTING 347
- Web Server Commands 348
- DISABLE HTTP SERVER 349
- ENABLE HTTP SERVER 350
- PURGE HTTP SERVER 351
- SET HTTP SERVER 352
- SHOW HTTP SERVER 357
- Encryption Key Commands 358
- CREATE ENCO KEY 359
- DESTROY ENCO KEY 363
- SET ENCO KEY 364
- SHOW ENCO 365
- Certificate Commands 366
- ADD PKI CERTIFICATE 367
- CREATE PKI CERTIFICATE 369
- CREATE PKI ENROLLMENTREQUEST 372
- DELETE PKI CERTIFICATE 374
- PURGE PKI 375
- SET PKI CERTIFICATE 376
- SET PKI CERTSTORELIMIT 378
- SET SYSTEM DISTINGUISHEDNAME 379
- SHOW PKI 380
- SHOW PKI CERTIFICATE 381
- Secure Sockets Layer (SSL) 382
- SHOW SSL 384
- Secure Shell (SSH) Commands 385
- DISABLE SSH SERVER 386
- ENABLE SSH SERVER 387
- SET SSH SERVER 390
- SHOW SSH 392
- TACACS+ and RADIUS 393
- ADD RADIUSSERVER 394
- ADD TACACSSERVER 395
- DELETE RADIUSSERVER 396
- DELETE TACACSSERVER 397
- DISABLE AUTHENTICATION 398
- ENABLE AUTHENTICATION 399
- PURGE AUTHENTICATION 400
- SET AUTHENTICATION 401
- SHOW AUTHENTICATION 403
- Management ACL Commands 404
- ADD MGMTACL 405
- DELETE MGMTACL 408
- DISABLE MGMTACL 409
- ENABLE MGMTACL 410
- SET MGMTACL STATE 411
- SHOW MGMTACL 412
Manuais e produtos relacionados com Hardware de computador Allied-telesis AT-S62
Hardware de computador Allied-telesis AT-VIEW PLUS 3.1 MIB COMPILER Manual do Utilizador
(14 páginas)
(14 páginas)
Hardware de computador Allied-telesis AT-VIEW PLUS 3.1 DEVICE MANAGER Manual do Utilizador
(118 páginas)
(118 páginas)
Hardware de computador Allied-telesis AT-VIEW PLUS 3.1 VLAN MANAGER Manual do Utilizador
(56 páginas)
(56 páginas)
Hardware de computador Allied-telesis AT-VIEW PLUS 3.1 INSTALLATION Manual do Utilizador
(26 páginas)
(26 páginas)
Hardware de computador Allied-telesis AT-VIEW PLUS 3.0 INSTALLATION Manual do Utilizador
(26 páginas)
(26 páginas)
Hardware de computador Allied-telesis AT-VIEW PLUS 3.0 VLAN MANAGER Manual do Utilizador
(52 páginas)
(52 páginas)
Hardware de computador Allied-telesis AT-VIEW PLUS 3.0 MIB COMPILER Manual do Utilizador
(14 páginas)
(14 páginas)
Hardware de computador Allied-telesis AT-VIEW PLUS 3.0 DEVICE MANAGER Manual do Utilizador
(127 páginas)
(127 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais